Molykote; Annually; Service Kit; Head Assembly - avdel Genesis G2LB Manual De Instrucciones

Ferramenta mecanica hidro-pneumatica
Ocultar thumbs Ver también para Genesis G2LB:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

S e r v i c i n g t h e To o l
A n n u a l l y
(or every 500,000 cycles whichever is the soonest)
Annually or every 500,000 cycles the tool should be completely dismantled and new components should be used where worn, damaged
or recommended. All 'O' rings and seals should be renewed and lubricated with Molykote
®

Molykote

111 for hydraulic sealing.
For an easy complete service, Avdel

SERVICE KIT : 71210-99990

PART Nº
07900-00667
PISTON SLEEVE
07900-00692
TRIGGER VALVE EXTRACTOR
07900-00670
BULLET
07900-00672
'T' SPANNER
07900-00706
'T' SPANNER SPIGOT
07900-00684
GUIDE TUBE
07900-00685
INSERTION ROD
07900-00351
3 MM ALLEN KEY
07900-00469
2.5 MM ALLEN KEY
07900-00158
2 MM PIN PUNCH
07900-00224
4 MM A/F ALLEN KEY
07900-00734
STOP NUT - MAXLOK
The employer is responsible for ensuring that tool maintenance instructions are given to the appropriate
The operator should not be involved in maintenance or repair of the tool unless properly trained.
The airline must be disconnected before any servicing or dismantling is attempted unless specifically instructed otherwise.
It is recommended that any dismantling operation be carried out in clean conditions.
Before proceeding with dismantling, empty the oil from the tool following the first three steps of the 'Priming Procedure' on page 19.
Prior to dismantling the tool it is necessary to remove the nose equipment. For instructions see the Nose Assemblies section, pages 8,
9 and 10.
For a complete service of the tool, we advise that you proceed with dismantling of sub-assemblies in the order shown.
After any dismantling REMEMBER to prime the tool and to fit an appropriate nose assembly.
H e a d A s s e m b l y
Unscrew Retaining Nut 26 and pull off stem collector assembly, items 18, 20, 21, 22, 23, 24 and 25.
Using the 'T' spanner*, remove End Cap Assembly 73 together with Seal 17, 'O' Ring 16, Lip Seal 28 and Spring 70.
Loosen Locknut 3 with a spanner* then unscrew Chuck Collet Adaptor 1.
Remove Locknut 3 together with 'O' rings 49 and 50.
Remove screw 9 and Bonded Seal 10.
Push Head Piston 7 to the rear and out of Head Assembly 4 taking care not to damage the cylinder bore.
Remove Seal Retainer 30. Push Lip Seal 8 to the rear and out of Head Assembly 4 taking care again not to damage the cylinder
bore.
Remove Seal Housing 5 and Lip Seal 67.
* Item included in the Service Kit.
Item numbers in bold refer to the General Assembly drawing and Parts List on pages 16-17.
14
®
is offering a complete service kit.
DESCRIPTION
®
I M P O R T A N T
Read Safety Instructions on page 4.
The tool should be examined regularly for damage and malfunction.
Spanners are specified in inches and across flats unless otherwise stated
PART Nº
07900-00164
CIRCLIP PLIERS
7
1
07900-00008
/
x
/
16
9
5
07900-00012
/
x
/
16
5
11
07900-00015
/
x
/
8
07900-00686
PEG SPANNER
07900-00677
SEAL EXTRACTOR
07900-00698
STOP NUT
07900-00700
PRIMING PUMP
07992-00020
GREASE - MOLY LITHIUM E.P.3753
07992-00075 GREASE - MOLYKOTE 55M
07900-00755 GREASE - MOLYKOTE 111
personnel.
®
55m grease for pneumatic sealing or
DESCRIPTION
®
SPANNER
2
SPANNER
8
SPANNER
16
®
®

Publicidad

Capítulos

Tabla de contenido
loading

Tabla de contenido