Philips SQM7441 Manual Del Usuario

Register your product and get support at
www.philips.com/support
User manual
Manual del usuario
En g l i s h
1 Important safety instructions
Caution
•
Read these instructions before you begin. If you are unsure
of any part of the process, contact a professional contractor
or installer for assistance. Improper installation can result in
injury or damage.
•
The wall or mounting surface must be capable of supporting
the combined weight of the mount and the display; if not, the
structure must be reinforced.
•
Locate pipes, wires, or any other hazards in the wall where
you wish to install the mount before drilling.
•
Safety gear and proper tools must be used. Failure to do so
can result in injury or damage.
•
Two people are recommended for installation. Do not
attempt to lift a heavy display without assistance.
•
Follow all instructions and recommendations regarding
adequate ventilation and suitable locations for mounting
your display. Consult the owner's manual for your particular
display for more information.
•
This wall mount is intended for use only with the maximum
weight of 25 kg (55 lbs). Use with heavier than the maximum
weights indicated may result in instability causing possible
injury.
2 Tilt wall mount (for LCD, Plasma, and LED
displays)
What's in the box
Wall plate (x1)
Mount arm (x2)
User manual (x1)
Hardware kit (x1)
Hardward kit
M8 x 63 screw (x2) M6 x 12 screw (x4)
A E
Lag bolt washer (x2) M8 x 12 screw (x4)
B F
Concrete anchor (x2) M6 washer (x4)
C G
M4 x 12 screw (x4) M8 washer (x4)
D H
Tools required
•
Phillips head screw driver
•
Ratchet or driver with 13 mm (1/2") socket
•
Electric or portable drill
•
6 mm (1/4") drill bit and stud finder for drywall
installation
•
10 mm (3/8") Masonry bit for concrete installation
sqm7441_27_2L_um_150731.indd 1-3
A
B
SQM7441
1
4
5
3 Installation
Mount to the drywall
Caution
For safety reasons, this mount must be secured to at least two
wood studs no less than 16" apart. The studs must be capable
of supporting the combined weight of the mount and display.
1 Use a high quality stud finder to locate two adjacent
studs where you wish to install your mount. Mark
both edges of each stud to help identify the exact
center.
Note
You must use the center of each stud to avoid cracking or
splitting the wood during installation.
2 Place the wall plate against the wall with the arrow
pointing up and level it using the integrated bubble
level.
3 While another person holds the wall plate in
position, mark two locations (one per stud) for
securing the mount to the wall (see Fig. 1).
4 Set the wall plate aside and drill a 6 mm (1/4") pilot
hole at each marked location.
5 Place the wall plate back against the wall and attach
it using the lag bolts
provided (see Fig. 2). Do not over-tighten these
bolts and do not release the wall plate until both
bolts are in place. Ensure that the wall plate remains
level after tightening the bolts.
Mount to the concrete wall
Caution
For safety reasons, the concrete wall must be capable of
supporting the combined weight of the mount and the display.
The manufacturer takes no responsibility for failure caused by
walls of insufficient strength.
1 Place the wall plate against the wall in the desired
location and level it using the integrated bubble level.
2 While another person holds the wall plate in place,
mark two locations on the wall for securing the
mount (see Fig. 3).
3 Set the wall plate aside and drill a 10 mm (3/8") hole
at each marked location. Remove any excess dust
from the holes.
4 Insert a concrete anchor
it is flush with the concrete surface (see Fig. 4). A
hammer can be used to lightly tap the anchors into
place if necessary.
Note
If the concrete wall is covered by a layer of plaster or drywall,
the concrete anchor must pass completely through the layer
to rest flush with the concrete surface.
D
C E
2
6
*
and lag bolt washers
A B
into each hole so that
C
F H
G
3
*
5 Place the wall plate back against the wall and attach
it using the lag bolts and lag bolt washers
A
provided (see Fig. 2). Do not over-tighten these
bolts and do not release the wall plate until all
bolts are in place. Ensure that the wall plate remains
level after tightening the bolts.
Attaching the mount arms to the display
Caution
Use extra care during this part of the installation. If possible,
avoid facing down your display as it may damage the viewing
surface.
Note
This mount comes with a selection of different screw
diameters and lengths to accommodate a wide variety of
display models. Not all of the hardware in the kit will be
used. If you cannot find the appropriate screw size in the kit
provided, consult the manufacturer of your display for more
information.
1 Determine the correct diameter of screw to use
carefully by trying different size (M4, M6 and M8)
from the hardware kit (see Fig.5). Do not force
any of the screws – if you feel resistance, stop
immediately and try a smaller diameter screw.
2 Attach the mount arms to the back of your display
using the screws identified in steps 1. If you are using
M6 screws you will need to use M6 washers
you are using M8 screws you will need to use M8
washers
H
Note
The mount arms must be attached with the tilt adjustment
screws facing towards the outer edges of the display (see Fig.
6). Otherwise, the tilt function cannot be accessed..
Final assembly
1 Loosen both tilt adjustment screws and set the tilt
to the desired angle. Make sure both arms are set
to the same angle before re-tightening both screws
securely.
2 With the help of another person, carefully lift your
display and place it on the wall plate. Gently apply
pressure to the bottom of your display so that the
clips on the mount arms lock to the wall plate. Do
not release the display until the mount arms have
securely hooked onto the wall plate.
Caution
Make sure that both arms are locked to the wall plate. For
safety reasons, this mount cannot be used unless both arms
are securely locked.
B
. If
G
31/07/2015 14:56:54