Milwaukee 2674-20 Manual Del Operador página 5

MAINTENANCE
To reduce the risk of injury, always
WARNING
unplug the charger and remove the
battery pack from the charger or tool before
performing any maintenance. Never disassemble
the tool, battery pack or charger. Contact a
MILWAUKEE service facility for ALL repairs.
Maintaining Tool
Keep your tool, battery pack and charger in good
repair by adopting a regular maintenance program.
Inspect your tool for issues such as undue noise,
misalignment or binding of moving parts, breakage of
parts, or any other condition that may affect the tool
operation. Return the tool, battery pack, and charger
to a MILWAUKEE service facility for repair. After six
months to one year, depending on use, return the
tool, battery pack and charger to a MILWAUKEE
service facility for inspection.
If the tool does not start or operate at full power with
a fully charged battery pack, clean the contacts on
the battery pack. If the tool still does not work prop-
erly, return the tool, charger and battery pack, to a
MILWAUKEE service facility for repairs.
Keep jaws clean. Lubricate moving parts of jaws to
prevent wear. Jaws should open easily and spring
back to a closed position. Inspect the jaws for cracks
or other damage. Do not use damaged jaws. Do not
attempt to repair jaws.
For
Press Jaws for use with
Viega PureFlow Fittings:
®
Use the supplied gauge to
heck for excess flash or flag
c
on the fitting. If the crimped
fitting diameter is too large
to fully enter the gauge, or
the flash/flag on the fitting
prevents the gauge from
seating flush to the fitting,
repeat with another fitting. If
the flash/flag continues to fail
the gauge test, the jaws may
be damaged. Replace the
jaws before continuing use.
CAUTION! Do not continue
to use jaws that continually
create excess flash/flag. Failure of the crimp could
occur.
For Crimp Jaws for use with Fittings designed to
F1807 & F2159 standards, the crimped fitting diameter
must fit fully in the gauge.
is too large to fully enter the gauge, the tool or jaws
may need to be serviced.
To reduce the risk of personal in-
WARNING
jury and damage, never immerse
your tool, battery pack or charger in liquid or
allow a liquid to flow inside them.
Cleaning
Clean dust and debris from vents. Keep handles
clean, dry and free of oil or grease. Use only mild
soap and a damp cloth to clean, since certain clean-
ing agents and solvents are harmful to plastics and
other insulated parts. Some of these include gasoline,
turpentine, lacquer thinner, paint thinner, chlorinated
cleaning solvents, ammonia and household deter-
gents containing ammonia. Never use flammable or
combustible solvents around tools.
Jaws
Acceptable
NOT Acceptable
If the crimped fitting diameter
For repairs, return the tool, battery pack and charger
to the nearest service center.
ACCESSORIES
Use only recommended accesso-
WARNING
ries. Others may be hazardous.
For a complete listing of accessories, go online to
www.milwaukeetool.com or contact a distributor.
Press Jaws for use with
Viega PureFlow
49-16-2630P
49-16-2631P
49-16-2632P
49-16-2633P
49-16-2634P
49-11-0080
Crimp Jaws for use with
Fittings designed to F1807 & F2159 standards
49-16-2630C
49-16-2631C
49-16-2632C
49-16-2633C
49-16-2634C
49-11-0081
SERVICE - UNITED STATES
1-800-SAWDUST
Monday-Friday, 7:00 AM - 6:30 PM CST
www.milwaukeetool.com
or visit
Contact Corporate After Sales Service Technical
Support with technical, service/repair, or warranty
questions.
Email: metproductsupport@milwaukeetool.com
Register your tool at www.milwaukeetool.com...
• to receive important notifications regarding your
purchase
• to ensure that your tool is protected under the warranty
• to become a Heavy Duty club member
SERVICE - CANADA
Milwaukee Tool (Canada) Ltd
1.800.268.4015
Monday-Friday, 7:00 AM - 4:30 PM CST
or visit www.milwaukeetool.ca
5
Repairs
Fittings
®
3/8" Viega PureFlow
®
1/2" Viega PureFlow
®
5/8" Viega PureFlow
®
3/4" Viega PureFlow
®
1" Viega PureFlow Fittings
®
Gauge
3/8" Fittings designed to
F1807 & F2159 standards
1/2" Fittings designed to
F1807 & F2159 standards
5/8" Fittings designed to
F1807 & F2159 standards
3/4" Fittings designed to
F1807 & F2159 standards
1" Fittings designed to
F1807 & F2159 standards
F1807 Gauge
(1.800.729.3878)
Fittings
Fittings
Fittings
Fittings