Milwaukee 2982-20 Manual Del Operador página 6

Sierra circular de corte para metal de 203 mm (8") de m18 fuel
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

4. Slide the lower guard lever up to raise the lower
guard. Remove the blade from the spindle. Always
clean the spindle, upper guard and lower guard to
remove any dirt and dust.
NOTE: Do not remove inner blade flange or
washer. Larger diameter of inner flange should
face the blade.
5. To install a blade, place the
blade on the spindle with
the teeth pointing in the
same direction as the ar-
row on the lower guard.
Release the lower guard lever.
6. Place the blade flange on the spindle and hand
tighten the bolt.
7. While holding in the spindle lock button, use the
wrench to turn the bolt clockwise and tighten.
8. Replace the chip container (see "Removing and
Installing Chip Container").
Adjusting Depth
1. Remove battery pack.
2. To adjust the depth of the cut, hold the saw by the
handle and loosen the depth adjusting lever by
pulling it up away from the shoe.
3. Raise or lower the shoe to the desired position. For
the proper depth setting, the blade should extend
no more than 1/4" below the material being cut.
4. Push down the depth adjusting lever to secure
the shoe position.
WARNING
to comply with ANSI Z87.1.
When working in dusty situations, wear appro-
priate respiratory protection or use an OSHA
compliant dust extraction solution.
Always remove battery pack before changing
or removing accessories. Only use accessories
specifically recommended for this tool. Others
may be hazardous.
Kickback causes and related warnings
-Kickback is a sudden reaction to a pinched, jammed
or misaligned saw blade, causing an uncontrolled saw
to lift up and out of the workpiece toward the operator;
-When the blade is pinched or jammed tightly by the
kerf closing down, the blade stalls and the motor reac-
tion drives the unit rapidly back toward the operator;
- If the blade becomes twisted or misaligned in the cut,
the teeth at the back edge of the blade can dig into
the top surface of the wood causing the blade to climb
out of the kerf and jump back toward the operator.
Kickback is the result of saw misuse and/or incorrect
operating procedures or conditions and can be avoided
by taking proper precautions as given below:
• Maintain a firm grip with both hands on the saw
and position your arms to resist kickback forces.
Position your body to either side of the blade,
but not in line with the blade. Kickback could
cause the saw to jump backwards, but kickback
forces can be controlled by the operator, if proper
precautions are taken.
• When blade is binding, or when interrupting a
cut for any reason, release the trigger and hold
the saw motionless in the material until the
blade comes to a complete stop. Never attempt
to remove the saw from the work or pull the saw
backward while the blade is in motion or kickback
may occur. Investigate and take corrective actions
to eliminate the cause of blade binding.
• When restarting a saw in the workpiece, centre
the saw blade in the kerf so that saw teeth are not
engaged into the material. If saw blade is binding,
it may walk up or kickback from the workpiece as the
saw is restarted.
• Support large panels to minimise the risk of blade
pinching and kickback. Large panels tend to sag
under their own weight. Supports must be placed
under the panel on both sides, near the line of cut
and near the edge of the panel.
• Do not use dull or damaged blades. Unsharpened
or improperly set blades produce narrow kerf causing
1/4"
excessive friction, blade binding and kickback.
• Blade depth and bevel adjusting locking levers
must be tight and secure before making cut. If
blade adjustment shifts while cutting, it may cause
binding and kickback.
• Use extra caution when sawing into existing walls
or other blind areas. The protruding blade may cut
objects that can cause kickback.
6
OPERATION
To reduce the risk of injury, always
wear proper eye protection marked

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

2982-21

Tabla de contenido