Functional Description - Makita HR5201C Manual De Instrucciones

8. Always be sure you have a firm footing. Be sure
no one is below when using the tool in high
locations.
9. Hold the tool firmly with both hands.
10. Keep hands away from moving parts.
11. Do not leave the tool running. Operate the tool
only when hand-held.
12. Do not point the tool at any one in the area when
operating. The bit could fly out and injure
someone seriously.
13. Do not touch the bit or parts close to the bit
immediately after operation; they may be
extremely hot and could burn your skin.
14. Some material contains chemicals which may be
toxic. Take caution to prevent dust inhalation and
skin contact. Follow material supplier safety data.
SAVE THESE INSTRUCTIONS.
WARNING:
MISUSE or failure to follow the safety rules stated in
this instruction manual may cause serious personal
injury.

FUNCTIONAL DESCRIPTION

CAUTION:
• Always be sure that the tool is switched off and
unplugged before adjusting or checking function on the
tool.
Switch action (Fig. 1)
FOR MODEL HR5211C
CAUTION:
• Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to the
"OFF" position when released.
To start the tool, simply pull the switch trigger. Release
the switch trigger to stop.
FOR MODELS HR5210C/HR5201C
Trigger switch
CAUTION:
• Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to the
"OFF" position when released.
• This switch functions when setting the tool in
and symbol modes.
To start the tool, simply pull the switch trigger. Release
the switch trigger to stop.
Slide switch
CAUTION:
• Before plugging in the tool, always check to see that
the tool is switched off.
• This switch functions only when setting the tool in
symbol action mode.
When using the tool in the hammering mode for a long
time, the slide switch is available. To start the tool, push
the "I (ON)" side of the switch lever. To stop the tool, push
the "O (OFF)" side of the switch lever. (Fig. 2)
AUTEK MAQUINARIA 5392 7077
Speed change (Fig. 3)
The revolutions and blows per minute can be adjusted just
by turning the adjusting dial. The dial is marked 1 (lowest
speed) to 5 (full speed).
Refer to the table below for the relationship between the
number settings on the adjusting dial and the revolutions/
blows per minute.
CAUTION:
• If the tool is operated continuously at low speeds for a
• The speed adjusting dial can be turned only as far as 5
Selecting the action mode
Rotation with hammering (Fig. 4 & 5)
For drilling in concrete, masonry, etc., depress the lock
button and rotate the change lever so that the pointer
points to the
bit.
Hammering only
FOR MODEL HR5201C AND HR5210C (Fig. 6)
For chipping, scaling or demolition operations, depress
the lock button and rotate the change lever so that the
pointer points to the
chisel, scaling chisel, etc.
For long time hammering (FOR MODELS HR5201C
AND HR5210C ONLY) (Fig. 7)
For chipping, scaling or demolition operations, depress
the lock button and rotate the change lever so that the
pointer points to the
chisel, scaling chisel, etc.
CAUTION:
• When using the tool in the
symbol
FOR MODEL HR5211C (Fig. 8)
For chipping, scaling or demolition operations, depress
the lock button and rotate the change lever so that the
pointer points to the
chisel, scaling chisel, etc.
CAUTION:
• Do not rotate the change lever when the tool is running
• To avoid rapid wear on the mode change mechanism,
AUTEK MAQUINARIA 5392 7077
Number on Revolutions per
adjusting dial minute
5
4
3
2
1
long time, the motor will get overloaded, resulting in
tool malfunction.
and back to 1. Do not force it past 5 or 1, or the speed
adjusting function may no longer work.
symbol. Use a tungsten-carbide tipped
symbol. Use a bull point, cold
symbol. Use a bull point, cold
trigger does not work and only the slide switch works.
symbol. Use a bull point, cold
under load. The tool will be damaged.
be sure that the change lever is always positively
located in one of the two or three action mode
positions.
Blows per minute
260 2,150
240 2,000
190 1,600
150 1,250
130 1,075
symbol mode, the switch
7