Milwaukee 2402-20 Manual Del Operador página 5

Selecting Drill or Drive Action
(Cat. No. 2402-20, 2403-20)
1. To use the drilling mode, rotate
the torque selector collar until the
drill symbol
with the arrow.
NOTE: The number selected on
the torque selector collar has no
effect on operation of the drill in
drilling mode.
2. To use the driving screws mode
rotate the application selector
collar until the drive symbol
pears in line with the arrow. Then
rotate the torque selector collar
until the desired clutch setting ap-
pears in line with the arrow.
The adjustable clutch, when properly adjusted, will
slip at a preset torque to prevent driving the screw
too deep into different materials and to prevent
damage to the screw or tool.
Selecting Hammer, Drill or Drive Action
(Cat. No. 2404-20)
1. To use the hammer-drilling mode,
rotate the application selector col-
lar until the hammer symbol
appears in line with the arrow.
Apply pressure to the bit to engage
the hammering mechanism.
NOTE: The number selected on
the torque selector collar has no effect on opera-
tion of the drill in hammer mode.
NOTE: When using carbide bits, do not use water
to settle dust. Do not attempt to drill through steel
reinforcing rods. This will damage the carbide bits.
2. To use the drilling only mode,
rotate the application selector col-
lar until the drill symbol
pears in line with the arrow.
NOTE: The number selected on
the torque selector collar has no
effect on operation of the drill in
drilling mode.
3. To use the driving screws mode
rotate the application selector col-
lar until the drive symbol
pears in line with the arrow. Then
rotate the torque selector collar
until the desired clutch setting ap-
pears in line with the arrow.
The adjustable clutch, when properly adjusted, will
slip at a preset torque to prevent driving the screw
too deep into different materials and to prevent
damage to the screw or tool.
Selecting Speed
The speed selector is on top of the motor housing.
Allow the tool to come to a complete
stop before changing speeds. See
"Applications" for recommended
speeds under various conditions.
1. For Low speed, push the speed
selector to display "1".
2. For High speed, push the speed
selector to display "2".
appears in line
ap-
ap-
ap-
If Using the Control Switch
The control switch may be set to three positions:
forward, reverse and lock. Due to a lockout mecha-
nism, the control switch can only be adjusted when
the ON/OFF switch is not pressed. Always allow the
motor to come to a complete stop before using the
control switch.
1. For forward (clockwise) rotation,
push in the control switch from the
right side of the tool. Check the
direction of rotation before use.
2. For reverse (counterclockwise)
rotation, push in the control switch
from the left side of the tool. Check
direction of rotation before use.
3. To lock the trigger, push the con-
trol switch to the center position.
The trigger will not work while
the control switch is in the center
locked position.
Always remove the battery pack
before performing maintenance or
changing accessories. Always lock
the trigger or remove the battery
pack before storing the tool and
any time the tool is not in use.
Starting, Stopping and Controlling Speed
1. To start the tool, grasp the handle firmly and pull
the trigger.
NOTE: An LED is turned on when the trigger is
pulled.
2. To vary the speed, increase or decrease the pres-
sure on the trigger. The further the trigger is pulled,
the greater the speed.
3. To stop the tool, release the trigger. Make sure
the bit comes to a complete stop before laying the
tool down.
Battery Pack Protection
To protect the battery from damage and extend its
life, the tool's intelligent circuit monitors current draw,
temperature, and voltage drops.
In extremely high torque, binding, stalling, and short
circuit situations that cause high current draw, the
tool will vibrate for about 5 seconds, the fuel gauge
will flash, and then the tool will turn OFF. To reset,
release the trigger.
Under extreme circumstances, the internal tem-
perature of the battery could become too high. If this
happens, the fuel gauge will flash and the battery
pack will shut off. Let the battery pack cool and then
continue work.
APPLICATIONS
To reduce the risk of electric shock,
WARNING
check work area for hidden pipes
and wires before drilling or driving screws.
Drilling in Wood, Composition Materials
When drilling in wood, composition materials and
plastic, select the
Start the drill slowly, gradually increasing speed as
you drill. When drilling into wood, use wood augers
or twist drill bits. Always use sharp bits. When using
twist drill bits, pull the bit out of the hole frequently to
clear chips from the bit flutes. To reduce the chance of
splintering, back work with a piece of scrap wood. Se-
lect low speeds for plastics with a low melting point.
5
and Plastic
drill-only operating mode.
Forward -
Push from
RIGHT
Reverse -
Push from
LEFT
Lock -
Push to
CENTER