Changing The Speaker Setting To Suit Your Speakers - Yamaha BD-S2900 Manual De Instrucciones

SETTINGS
■ "TV/Device Connection" (continued)
Component Resolution
This sets the video output resolution when using the component video terminal.
Speaker
You can set the unit to output the best possible sound for your speakers.
TV System
Change the setting to match the equipment you are connecting with.
• If picture output is not smooth, change the setting.
• When NTSC contents are played, they are outputted in the signal format
specified in the "NTSC Contents Output', irrespective of the settings here.

Changing the speaker setting to suit your speakers

When connecting to an amplifier/receiver to enjoy multi-channel surround sound, use the following settings on this unit if they cannot be set on the amplifier/receiver.
The settings are not effective when outputting bitstream signals.
Centre
Front (L)
ms
L
0.0
dB
0.0
Complete
Complete
Test
Test
dB
LS
LB
(LS) Surround (RS)
* Surround back channel is enabled only when the unit is connected to an amplifier/
receiver supporting HDMI 7.1 channel audio.
Speaker presence and size (
1 Press [
, , , ] to select the speaker icon (
2 Press [
, ] to select the setting and press [OK].
Icon examples:
Surround speaker (LS)
• Large: Select when the speaker supports
low-frequency (under 100 Hz)
reproduction.
• Small: Select when the speaker does not support low-frequency reproduction.
In order to make an ideal listening environment, settings of speaker sizes may be
automatically adjusted.
For example, if the subwoofer is set to "No", the front speakers will automatically be set
to "Large". (In this case, we recommend connecting a speaker that can reproduce bass
below 100 Hz.)
Delay time ( )
For optimum listening with 7.1/5.1-channel sound, all the speakers, except for the
subwoofer, should be the same distance from the seating position.
If you have to place the centre, surround and surround back speakers closer to the seating
position, adjust the delay time to make up for the difference.
If either distance or is less than
change to the recommended setting.
1 Press [
, , , ] to select the delay time box (
2 Press [
, ] to select the setting and press [OK].
22
En
Front (R)
dB
R
C
0.0
dB
0.0
Subwoofer
dB
SW
0.0
ms ms dB
RS
0.0 0.0 0.0
ms
RB
0.0
(LB) Surround back (RB)*
)
) and press [OK].
LS LS
Large Small
, find the difference in the relevant table and
) and press [OK].
• 576i/480i • 576p/480p
480i, 480p: When playing NTSC discs
576i, 576p: When playing PAL discs
Even if you select "720p" or "1080i", the video output resolution is restricted to "576p/480p"
when DVD-Video and BD-Video discs recorded at a rate of 50 frames per second is output
from the COMPONENT VIDEO OUT terminals.
• Multi Channel: When using 3 or more speakers. (] below)
• 2 Channel: When using two speakers.
2ch down-mix audio are output from Front L and Front R.
• NTSC: Select when connecting to a NTSC television.
• PAL: Select when connecting to a PAL or multi-system television.
5.1ch speaker connection
Approximate room dimensions
C
L C
LS
RS
LS
RS
Circle of constant primary listening distance
Centre speaker
Difference
Approx. 34 cm (1 ft. 1 in.)
Approx. 68 cm (2 ft. 2 in.)
Approx. 102 cm (3 ft. 4 in.)
Approx. 136 cm (4 ft. 5 in.)
Approx. 170 cm (5 ft. 6 in.)
Channel balance (
This does not work when connected with the HDMI terminal and "HDMI Audio Output"
(] 21) is set to "On".
1 Select "Test" and press [OK].
A test signal is output.
No
Front (L) Centre
Surround (LS) Surround Back (LB)*
* Test signal is output only when the unit is connected using HDMI AV OUT
terminal.
2 While listening to the test signal, press [
Front speakers: 0.0 to – 6.0 dB
Centre and surround speakers: 0.0 to –12.0 dB
• You cannot adjust the volume of surround back speakers.
3 Press [OK].
The test signal stops.
• No signal is output for the subwoofer. To adjust its volume, play something, then
return to this screen to adjust to suit your taste.
4 Press [
, , ,
• 720p • 1080i
7.1ch speaker
connection
C
R L C R
LS RS
SW LS RS
LB
RB
LB
RB
Surround/Surround back
speakers
Setting
1.0 ms Difference
2.0 ms Approx. 170 cm (5 ft. 6 in.)
3.0 ms Approx. 340 cm (11 ft. 1 in.)
4.0 ms Approx. 510 cm (16 ft. 8 in.)
5.0 ms
)
Front (R) Surround (RS)
Surround Back (RB)*
, ] to adjust the volume of each speaker
] to select "Complete" and press [OK].
: Actual
speaker
position
SW : Ideal speaker
position
: Primary listening
distance
Setting
5.0 ms
10.0 ms
15.0 ms