To Start To Use Husqvarna Connect; To Set The Cutting Height; To Start The Product; To Use The Save Function - Husqvarna LB 146i Manual De Usuario

• Information about, and help with, product parts and
servicing.

To start to use Husqvarna Connect

1. Download the Husqvarna Connect app on your
mobile device.
2. Register in the Husqvarna Connect app.
3. Do the instruction steps in the Husqvarna Connect
app to connect and register the product.

To set the cutting height

• Press the shaft out and move it to the correct
position for each of the 4 wheels. (Fig. 21)
CAUTION: Do not set the cutting height too
low. The blades can hit the ground if the
surface of the lawn is not level.
Battery
WARNING: Before you use the battery, you
must read and understand the safety
chapter. You must also read and understand
the operator's manual for the battery and the
battery charger.
Battery status
The display shows the remaining battery capacity and if
there are problems with the battery. The battery capacity
is shown for 5 seconds after the product is switched off
or the battery indicator button is pressed. The warning
symbol on the battery is on when an error has occurred.
Battery on page 17 .
See
(Fig. 22)
LED lights
All LEDs are lit
LED 1, LED 2, LED 3 are
lit
LED 1, LED 2 are lit
LED 1 is lit
LED 1 flashes
To charge the battery
Charge the battery before the first use. The battery is
only 30% charged when supplied to the customer.
Note: The battery charger must be connected to the
voltage and frequency specified on the rating plate.
14
Battery status
Fully charged (75-100%)
The battery is 50%-75%
charged
The battery is 25%-50%
charged
The battery is 0%-25%
charged.
The battery is empty.
Charge the battery.
The battery does not charge if the battery temperature is
above 50°C. The battery charger decreases the
temperature of the battery before it starts to charge.
1. Connect one end of the power cord for the battery
charger into the socket of the battery charger.
2. Connect the other end of the power cord for the
battery charger in an grounded mains socket. The
LED on the battery charger flashes green one time.
(Fig. 23)
3. Put the battery in the battery charger. The green light
on the charger comes on when the battery is
correctly connected to the battery charger. (Fig. 24)
4. When all LEDs on the battery have come on the
battery is fully charged. Charge the battery for
maximum 24 hours.
5. To disconnect the battery charger from the mains
socket, pull the plug, not the power cord.
6. Remove the battery from the battery charger.
Battery charging status
A Husqvarna Li-ion battery can be charged or used at all
charging levels. The battery is not damaged. A fully
charged battery will not decrease its charge when the
battery is left in the charger.
LED display
LED 1 flashes
LED 1 is lit, LED 2 flashes 25%-50%
LED 1, LED 2 are lit, LED
3 flashes
LED 1, LED 2, LED 3 are
lit, LED 4 flashes
LED 1, LED 2, LED 3,
LED 4 are lit

To start the product

1. Put a charged battery in battery compartment
number 1 below the battery lid. For longer operation
time, put a second charged battery in battery
compartment number 2.
2. Turn the safety key to 1. (Fig. 15)
3. Stay behind the product.
4. Press the ON/OFF button (A) on the control panel
and the green LED (B) comes on. (Fig. 25)
5. Loosen the start inhibitor. (Fig. 17)
6. Push the motor brake handle in the direction of the
handlebar. (Fig. 26)

To use the SavE function

The product has a battery saving function (SavE) that
gives longer operation time.
Charging status
0%-25%
50%-75%
75%-100%
Fully charged
901 - 003 - 25.10.2018