DeLonghi DTT02 Serie Instrucciones Para El Uso página 5

Use the carriage lever to lift the toast to Peek & View™ at
any time without cancelling the toasting cycle.
Before plugging in
- Make sure your electricity supply is the same as the one
shown on the underside of your toaster.
- This appliance conforms to EC directive 2004/108/EC on
Electromagnetic Compatibility and EC regulation no.
1935/2004 of 27/10/2004 on materials intended for con-
tact with food.
Before using for the first time
1 Clip excess cord into the cord storage clips in the base 1.
- Operate the toaster once on a medium setting without
bread. (The lever will not stay down unless the toaster is
plugged in).
- As with all new heating elements, your toaster may emit a
slight burning smell when it is first switched on. This is
normal and not a cause for concern.
To use your toaster
1 Plug the toaster into the power supply.
2 Move the browning control to the desired setting. Use a
low setting
for light toasting and for thin or dry bread.
3 Insert the bread, muffins, bagels etc.
4 Lower the lever until it locks 2. The 'cancel' button will illu-
minate. (The lever will not stay down unless the toaster is
plugged in).
- To toast frozen bread, move the browning control to the
defrost position .
- Use the carriage lever to lift the toast to Peek & View™ at
any time without cancelling the toasting cycle.
- To stop toasting during the cycle, press the 'cancel' button,
the toast will pop up and the 'cancel' button light will go
off.
5 Your toast will pop up automatically, to raise it higher,
lift the lever.
Hints on using your toaster
- Select a lower setting for light browning, for toasting one
slice only or for dry bread.
- When toasting a single slice of bread, you may notice a
variation in toast color from one side to the other - this is
normal.
- Dry/stale bread toasts more quickly than fresh bread and
thinly sliced bread toasts more quickly than thickly sliced
bread. Therefore, the browning control should be set at a
lower setting than usual.
- For best results ensure that the bread slices are of an even
thickness, freshness and size.
- In order to achieve uniform browning we recommend you
wait a minimum of 30 seconds between each toasting so
that the control can automatically reset.
Alternatively, select a lower setting when additional toast-
ing is carried out.
Warming rack safety
1 Never set the browning control higher than 1 when using
the warming rack.
2 Never completely cover the warming rack.
3 When using the warming rack, never wrap the food up.
Plastic wrapping will melt and could catch fire. Foil will
reflect heat, damaging the toaster.
4 If you're using the toaster slots, always remove the warm-
ing rack so it can't burn you.
5 Always allow the warming rack to cool before removing
from the toaster. Never place a hot warming rack on a
work surface.
6 Never touch hot surfaces, especially the metal areas of the
warming rack.
To use the warming rack
1 Place the warming rack on top of toaster 3.
2 Put your food on top of the rack (slicing thick items in half
will speed up the warming process).
3 Set the browning control no higher than 1
4 Lower the lever.
5 At the completion of the warming cycle the toaster will
switch off automatically. Turn the items over and repeat
the operation. Watch to make sure they don't burn.
6 To remove the warming rack, allow the toaster to cool and
unplug.
7 Lift off the warming rack.
Hints for the warming rack
- The warming rack can also be used as a toast rack, but
ensure it is cool before removing from the toaster.
Care and cleaning
1 Before cleaning, unplug your toaster and let it cool down.
2 Slide out the crumb tray 4. Clean, then replace. Do this reg-
ularly: crumbs can smoke or even burn.
3 Wipe the outside of the toaster and the warming rack with
a damp cloth, then dry. Do not use abrasives.
.
5