Fuels/Refuelling; Storage Of Fuel - Dolmar MS-34 U Instrucciones De Manejo

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 107

FUELS/REFUELLING

Handling petroleum products
Utmost care is required when handling fuel. Fuel may contain substances similar
to solvents. Refuel either in a well ventilated area or outdoors. Do not inhale fuel
vapors, avoid any contact of fuel or oil with your skin.
Mineral oil products degrease your skin. If your skin comes in contact with these
substances repeatedly and for an extended period of time, various skin diseases
may result. In addition, allergic reactions are known to occur. Eyes can be irritated
by contact with oil, fuel etc.
If oil comes into your eyes, immediately wash them with clear water.
If your eyes are still irritated, see a doctor immediately.
Fuel and oil mixture
The engine of the brushcutter is a high-efficiency two-stroke engine.
It is run with a mixture of fuel and two-stroke engine oil. The engine is designed
to use unleaded regular fuel with a min. Octane value of 91 RON. If no such fuel
is available, you can use fuel with a higher octane value. This will not affect the
engine, but may cause poor operating behavior.
A similar situation will arise from the use of leaded fuel. To obtain optimum engine
performance and to protect your health and the environment, only unleaded fuel
should be used!
For engine lubrication use a two-stroke engine oil (quality grade: JASO FC or ISO
EGD), which is added to the fuel. The engine has been designed to use DOLMAR
two-stroke engine oil at mixture ratio of 50:1 to protect the environment. In addition,
a long service life and reliable operation with a minimum emission of exhaust
gasses is assured. It is absolutely essential to observe a mixture ratio of 50:1
DOLMAR 2-stroke engine oil. Otherwise reliable function of the brushcutter cannot
be guaranteed.
The correct mixture ratio:
Mix 50 parts gasoline with 1 part DOLMAR 2-stroke engine oil (see table on right).
O
:
r r
arin
u l il mi ur
half of the fuel required in an approved can which meets or exceeds
all local code standards, then add the remaining fuel. Throughly shake
mi ur
r
a
m r
n in
il
only result in a higher production of combustion residues which will
pollute the environment and clog the exhaust channel in the cylinder,
ar
lu
a
will rise and the performance will be decreased.
Refuelling
Never perform refuelling operations in a closed, unventilated area.
The engine must be switched off!
– Thoroughly clean the area around the tank cap, to prevent dirt from getting into
the fuel tank (1).
– Unscrew the tank cap (2) and fill the tank with fuel.
– Never fill the fuel tank to the very top.
– Securely screw on the tank cap.
– Wipe the screw plug and tank with an absorbent after refuelling!
Allow cloths to dry and discard in a proper container.
NOTE: In some countries, the tank cap does not have the strap (3).

Storage of Fuel

Fuel cannot be stored for an unlimited period of time.
Purchase only the quantity required for a 4 week operating period. Only use
approved fuel storage containers.
r
mi
n ir
llin i in
ru
u
r an
an
i
n ur
a
ll a
mu
r n a
i i n u l
Observe the Safety Instructions on page 4!
(premium unleaded)
il uan i
i
i n
i
ra i n
i
ill
10,000 cc (10 L)
n um i n
12
Gasoline
+
1,000 cc (1 L)
5,000 cc (5 L)
(1)
50:1
20 cc
100 cc
200 cc
(3)
(2)

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Ms-34 c

Tabla de contenido