Part Description - Oregon 310-230 Manual De Instrucciones

EN
- These guards must always be fitted in place when the machine is in use .
- Always make sure the guards are efficient and fitted properly . Operator
safety could be compromised if the guards are damaged and/or cracked .
Switch: the machine features a safety switch with release coil . In the case of
a sudden power failure, the switch trips automatically and disconnects the
machine from the mains . The machine will not start even if the power supply is
suddenly restored . You need to reset the switch to start the machine again .
INTENDED USE
This machine is an electrical grinder for chains used on chain saws .
Use the machine exclusively for the types of chains
stated in the technical data chart .
Do not use the machine to cut or grind anything
other than the chains recommended .
Secure the machine firmly to the bench or wall .
The machine must not be used in corrosive or explosive environments .
Any other use is to be considered improper .
The manufacturer is not liable for damages following
improper or incorrect use of the machine .

Part Description

See Illustration, page 2 .
The grinder is supplied already partially assembled .
A . Motor unit
B . Vise assembly
C . Grinding wheels:
5 3/4" x 1/8" x 7/8" (145 x 3,2 x 22,2 mm)
5 3/4" x 3/16" x 7/8" (145 x 4,7 x 22,2 mm)
D . Sharpening template
E . Dressing brick
F . Motor brushes (2)
1 . Operating handle
2 . Grinding wheel guard
3 . Grinding wheel guard screws (3)
4 . Grinding wheel flange knob
5 . Grinding wheel flange
6 . Depth adjustment knob
7 . Chain stop adjustment knob
8 . Chain stop
9 . Vise handle
10 . Vise (chain jaws)
11 . Vise rotate angle guide plate
12 . Vise adjustment knob
13 . Vise reference mark pointers
Instrumental Measurements
A Measure the gauge depth using the suitable shape .
B Measure the cutter length .
C Measure the chain pitch .
4
Stopping and Shutting Down
Stopping
Turn the machine off by turning the switch to position "0"
and unplug the power cable from the mains .
Shutting Down
Once you have finished using the machine, disconnect it and clean it thoroughly .
Store it in a dry and safe place, protected against dust and damp .
Handling and Transport
If you need to transport the machine, take it off the bench
or wall, dismantle the grinding wheel and put all the parts
in a packing box to protect them against impact .
Demolition and Disposal
The machine is to be demolished by qualified personnel in compliance
with current laws in the country in which it is installed .
Before you scrap the machine, make it unusable by cutting the power
supply cable for example and make the parts safe, which could cause
a source of danger for children if they should play with the machine .
Warranty and Service
The warranty validity is that acknowledged in the country of sale . Claims
under warranty will only be accepted if they are backed up by the copy of
the purchase document (bill or receipt) . The guarantee becomes void if:
- The machine has been tampered with;
- The machine has not been used according to this manual;
- Non-original parts, machines or grinding wheels have been fitted on the
grinder or other parts that are not authorised by the manufacturer;
- The machine has been powered at a voltage or frequency
different from that written in the rating nameplate .
Limited Warranty
At Oregon, our goal is help you get the job done right with outstanding
products that perform to your full satisfaction . Oregon | Blount, Inc .
warrants its products to be free from defects in materials and workmanship
for as long as they are owned by the original retail purchaser .
If for any reason, you are not satisfied with our products, please
let us know . Our contact information is listed below .
LIABILITY UNDER THIS WARRANTY IS LIMITED TO REPLACEMENT
PARTS, AT THE OPTION OF YOUR OREGON DISTRIBUTOR AND OREGON .
PLEASE CONTACT YOUR OREGON DISTRIBUTOR OR US DIRECTLY . OREGON
PRODUCTS ARE NOT WARRANTED AGAINST NORMAL WEAR AND TEAR,
USER ABUSE, IMPROPER MAINTENANCE OR IMPROPER REPAIR .
REPLACEMENT OF DEFECTIVE PRODUCT IS THE EXCLUSIVE REMEDY
UNDER THIS WARRANTY AND ANY APPLICABLE IMPLIED WARRANTY . THE
REPLACEMENT WILL BE UNDERTAKEN AS SOON AS REASONABLY POSSIBLE
AFTER RECEIPT OF THE DEFECTIVE PRODUCT . TO THE EXTENT PERMITTED
BY LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE APPLICABLE TO THIS PRODUCT IS LIMITED TO THE
DURATION AND SCOPE OF THIS EXPRESS WARRANTY . OREGON SHALL NOT
BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES . SOME
STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY
LASTS OR DO NOT ALLOW THE EXCLUSION OF CONSEQUENTIAL DAMAGES,
SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU . THIS
WARRANTY GIVES THE ORIGINAL OWNER SPECIFIC LEGAL RIGHTS, AND YOU
MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE .
If you have questions regarding Oregon products, please visit
OregonProducts .com
310-230