Additional Safety Rules For The Laser; Power Connections; Motor Specifications; Grounding Instructions - BLACK&DECKER BT2000L Manual De Instrucciones

ADDITIONAL SAFETY RULES FOR THE LASER

For your convenience and safety the
following labels are on your tool.
ADVERTENCIA
ADVERTÊNCIA
WARNING
RADIACION LASER. NO MIRE FIJAMENTE
HACIA EL RAYO. PRODUCTO LASER DE
CLASE 2 • RADIAÇÃO DE LASER! NÃO OLHE
DIRETAMENTE AO FEIXE. LASER CLASSE 2
• LASER RADIATION. DO NOT STARE INTO
BEAM. CLASS 2 LASER PRODUCT.
Sujete correctamente el
soporte. Ajuste los tornillos
antes de usar la herramienta. • Prenda
o suporte corretamente. Aperte os
parafusos antes de utilizar a
ferramenta • Properly secure
bracket. Tighten screw before use.
Fig. A
Fig. B
Before connecting the machine to the power line, make sure the switch is in the "OFF" position and be sure that the
electric current is of the same characteristics as indicated on the machine. All line connections should make good
contact. Running on low voltage will damage the machine.
DO NOT EXPOSE THE MACHINE TO RAIN OR OPERATE THE MACHINE IN DAMP LOCATIONS.
Your machine is wired for: 220V ~ 50Hz (Argentina y Chile) 127V/220V ~ 60Hz (Brazil), 120V ~ 60Hz (CCA, Colombia
& México). Before connecting the machine to the power source, make sure the switch is in the "OFF" position.
THIS MACHINE MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROM
ELECTRIC SHOCK.
1. All grounded, cord-connected machines:
In the event of a malfunction or breakdown, grounding
provides a path of least resistance for electric current to
reduce the risk of electric shock. This machine is
equipped with an electric cord having an equipment-
grounding conductor and a grounding plug. The plug
must be plugged into a matching outlet that is properly
installed and grounded in accordance with all local
codes and ordinances.
Do not modify the plug provided - if it will not fit the
outlet, have the proper outlet installed by a qualified
electrician.
Improper connection of the equipment-grounding
conductor can result in risk of electric shock. The
conductor with insulation having an outer surface that
is green with or without yellow stripes is the
FOR LASER SAFETY OBSERVE THE FOLLOWING:
LASER LIGHT - DO NOT STARE INTO BEAM, APERTURE, or into a reflection
•
from a mirror-like surface Fig. A & B.
AVOID EXPOSURE - LASER LIGHT IS EMITTED FROM FRONT GUARD
•
APERTURE. Use of controls or adjustments, or performance of procedures
other than those specified herein may result in hazardous laser light exposure.
DO NOT DISASSEMBLE LASER MODULE. The laser is a CLASS II LASER
•
PRODUCT that can emit laser power up to 1 mW MAX at 650 nm, which could
result in exposure with the module disassembled. The laser unit complies with
21 CFR 1040.10 and 1040.11.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
•
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
THE USE OF OPTICAL INSTRUMENTS with this product will increase eye
•
hazard.
• LASER RADIATION, avoid direct eye exposure, serious eye injury can result.
• DO NOT OPERATE IN EXPLOSIVE ATMOSPHERES, such as in the presence of
flammable liquids, gases, or dust.
• USE ONLY WITH THE SPECIFICALLY DESIGNATED BATTERIES. Use of any
other batteries may create a risk of fire.
• USE ONLY ACCESSORIES that are recommended by the manufacturer for your
model.
• ACCESSORIES THAT MAY BE SUITABLE FOR ONE LASER, may create a risk of
injury when used on another laser.
187820-00
• REPAIRS AND SERVICING MUST be performed by a qualified repair facility.
Repairs performed by unqualified personnel could result in serious injury.
• DO NOT REMOVE OR DEFACE WARNING LABELS. Removing labels increases
the risk of exposure to radiation.
• THIS PRODUCT IS INTENDED for use in a temperature range of 41°F(5°C) -
104°F(40°C).

POWER CONNECTIONS

MOTOR SPECIFICATIONS

GROUNDING INSTRUCTIONS

equipment-grounding conductor. If repair or
replacement of the electric cord or plug is necessary,
do not connect the equipment-grounding conductor to
a live terminal.
Check with a qualified electrician or service personnel if
the grounding instructions are not completely
understood, or if in doubt as to whether the machine is
properly grounded.
Use only 3-wire extension cords that have 3-prong
grounding type plugs and matching 3-conductor
receptacles that accept the machine's plug, as shown in
Fig. C. Repair or replace damaged or worn cord
immediately.
46