EINHELL TC-RO 1155 E Manual De Instrucciones página 33

6.3 Adjusting the routing depth (Fig. 14 – 17)
•
Place the machine on the workpiece.
•
Undo the wing screw (16) and fixing handle
(9).
•
Slowly move the machine downwards until
the cutter makes contact with the workpiece.
•
Tighten the fixing handle (9).
•
Set the fine adjuster (15) to 0 as shown in Fig.
17.
•
Adjust the revolver end stop (14) so that the
depth stop (19) is above the end stop (a) set
to the lowest height.
•
Lower the depth stop (19) until it touches the
end stop (a). Then tighten the wing screw
(16).
•
Set the pointer (17) to the zero point on the
scale (18).
•
Undo the wing screw (16). Push the depth
stop (19) upwards until the pointer (17) points
at the required cutting depth on the scale
(18). Tighten the wing screw again.
•
Test the setting by completing a test cut on a
waste piece.
•
Now you can carry out the final adjustment
of the cutting depth. To do this turn the fine
adjuster (15) to the required dimension.
Turn the fi ne adjuster (15) counter-clockwise: gre-
ater cutting depth
Turn the fi ne adjuster (15) clockwise: lower cutting
depth
Turning the fi ne adjuster (15) through one division
corresponds to a change of cutting depth of 0.04
mm, one whole turn corresponds to 1 mm.
On the precision adjustment device (15) you
can also turn the lower ring (b) separately. This
lets you reach the zero point without altering the
precision adjustment device (15). See Fig. 17 and
proceed as follows:
•
Press down the ring (b).
•
Hold and turn it until you have reached the
desired position.
•
Release the ring again.
Anl_SA_Anl_TC_RO_1155_E_SPK8.indb 33 Anl_SA_Anl_TC_RO_1155_E_SPK8.indb 33
GB
6.4 Routing
•
To avoid damage to the router, make sure
there are no foreign objects attached to the
workpiece.
•
Connect the mains plug to a suitable socket.
•
Hold the tool using both of its handles (7).
•
Place the router on the workpiece.
•
Set the cutting depth as described in point
6.3.
•
Select the speed as described in point 6.2
and switch the machine on (see point 6.1).
•
Test the machine settings using a piece of
waste.
•
Operate the tool at full speed. Only then
should you lower the router to its working
height and lock the machine with the locking
grip (9).
Cutting direction: The cutting tool turns clock-
wise. To avoid accidents you must always cut
against the direction in which the tool turns (Fig.
18).
Feed speed: It is very important to machine
the workpiece at the correct feed speed. We
recommend that before you machine the actual
workpiece, you carry out several trial cuts on a
waste piece of the same type. This will enable you
to fi nd the best working speed for the workpiece
very easily.
Feed speed too low:
The cutter could heat up excessively. If you are
cutting infl ammable material such as wood, the
workpiece could ignite.
Feed speed too high:
The cutter could be damaged. Cutting quality:
Rough and uneven.
Allow the cutter to come to a complete standstill
before removing the workpiece or putting down
the router.
6.5 Routing in stages
Depending on the hardness of the material you
wish to cut and the cutting depth, it may be a
good idea to proceed in stages.
•
If you wish to route in several stages, turn the
end stop revolver (14) after you have set the
cutting depth as described in point 6.3 so that
the depth stop (19) is over the highest end
stop (a).
•
Now route in this setting. After completing the
first routing operation, adjust the end stop
- 33 -
25.05.2018 09:23:03 25.05.2018 09:23:03