Setting The Transmitter - Monacor International JTS IN-264TH/5 Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

5.1 Setting the transmitter

When the transmitter is not locked, press the but-
ton SET (4) to activate the setting modes one after
another:
group (keep button pressed for a while)  channel
 sensitivity  transmission power
 automatic frequency matching
 identification number  lock function
To make settings in a setting mode, see the corre-
sponding chapter (5 1 1 to 5 1 6)
To exit a setting mode without changing a setting,
press the button SET repeatedly until the display
briefly shows
the normal mode
5.1.1 Transmission frequency (group / channel)
To set the transmitter quickly and easily to the
transmission frequency of the receiver unit, use the
REMOSET function (
it is also possible to set the transmission frequency
of the transmitter manually by selecting the chan-
nel group and the channel The table on page 20
gives an overview of the groups and channels
1) Keep the button SET (4) pressed until the display
briefly shows
(
...
) starts flashing; the group setting mode
is activated
2) Select the group with the button
button
(5)
3) Press the button SET to confirm The channel
indication starts flashing on the display; the
channel setting mode is activated
4) Select the channel with the button
button
5) Press the button SET to confirm The display
briefly shows
the normal mode
5.1.2 Sensitivity
For the microphone sensitivity, several levels are
available: from 12 dB (maximum sensitivity) to
−18 dB (minimum sensitivity)
1) Keep the button SET (4) pressed until the display
briefly shows
mode (group indication starts flashing)
2) Press the button SET repeatedly until the dis-
play briefly shows
sensitivity
10
The unit will then return to
chapter 5, step 3) However,
Then the group indication
(3) or the
The unit will then return to
and then the group setting
and then the current
3) Use the arrow buttons to set the sensitivity in
such a way that you obtain an optimum vol-
ume level of the microphone If the volume is
too high, the microphone will distort; in this
case, set a lower value with the button
If the volume is too low, there will be a poor
signal-to-noise ratio; in this case, set a higher
value with the button
4) Press the button SET to confirm The display
briefly shows
the normal mode
5.1.3 Transmission power
For the transmission power, two values are avail-
able With a high transmission power, the range
will increase; however, the operating time of the
batteries will decrease due to faster discharge
1) Keep the button SET (4) pressed until the display
briefly shows
mode (group indication starts flashing)
2) Press the button SET repeatedly until the display
shows the current transmission power:
3) Press the button
or press the button
4) Press the button SET to confirm The display
briefly shows
the normal mode
5.1.4 Automatic frequency matching
(REMOSET function)
or the
To enable /disable the automatic frequency match-
ing (REMOSET function = frequency setting of the
transmitter via a radio signal of the receiver unit)
for the transmitter:
1) Keep the button SET (4) pressed until the display
briefly shows
mode (group indication starts flashing)
2) Press the button SET repeatedly until the display
shows the current setting for the automatic fre-
quency matching:
(5)
The unit will then return to
and then the group setting
low transmission power (10 mW)
high transmission power (50 mW)
(3) to select the setting
(5) to select the setting
The unit will then return to
and then the group setting
automatic frequency matching enabled
(i e frequency setting of the transmitter
via the REMOSET function is possible)
automatic frequency matching disabled
(i e no REMOSET transmission)
(3)

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Jts 25.5440

Tabla de contenido