Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
No final spin
The indicator light "no final spin" is lit
red.
For delicate laundry, the water remains
in the machine after the last rinse.
Use this setting to avoid creasing if the
clothing cannot be taken out of the
washing machine immediately upon
completion of the cycle.
Before unloading you must drain the
remaining water by selecting Drain
or Spin and starting the machine.
Modifiers
Spin Selection
Preset cycle setting of max. spin speed
can be changed.
Max spin
Reduced spin
@ Gentle spin
Q No final spin
@@
_eiay
Press this button until the desired
setting lights up.
Delay Start
Before starting a program you can
modify by when the cycle should be
started.
_9
s
@
@ d:
s
@ Fin h_d
i
.............
@ _/'? i:?/}
[
S [_illl
@/}no
ocked [
i
E
sellec_i0s _
I
I
[
Press Delay Start button. The display
shows the start time 0:00.
The time can be delayed up to a
maximum of 19 hours (with 1 hour
increments) by pressing the Delay
Start button again.
The Start time begins running
immediately after pushing the
Start/Pause
button. This is indicated
by the points between the digits
flashing.
F_
Changes to the Start time are
possible at any time, press the
Delay Start button until the new
time appears.
[_lf
the program is changed or if the
program is interrupted, the
preselected Start time is also
interrupted. The Ready in time of
the program is displayed. The
Start time must be reselected.
Option buttons
Bleach
8b
When tnls DuKon S oressea,
a Dleacn
cycle will be added to the selected
cy@e.
The wasntn9 cycle time is extenaea
accordin@y.
Rinse
Plus
O
When tnls DuKon s eressed,
an
aaamona
nnsng c}@e N_ De aaaea to
me selected
cy@e.
Washing
cy@e time
s extenaea
accor@n@y.
Heavy duty
O
The Heaw duty option is
recommended for use ONLY for
heavily soiled clothes that require
the removal of tough, ground-in
protien-based
stains. It is NOT
recommended to use the Heaw duty
option with other cycles when
laundering normal or lightly soiled
clothes.
Washing time is extended.
Only cold water is introduced to the
drum. The washing machine then
heats the water to the selected wash
temperature. By raising the
temperature
from cold up to the set
temperature all components of the
detergent are activated in stages for
best stain removal and cleaning results.
Acoustic
Signal
An acoustic signal indicates program
statuses (e.g. start/end of program and
operating faults.)
To activate the signal:
Select a program.
Press two of the Option
Buttons(e.g. Bleach and Rinse
Plus) until a long signal is emitted.
To deactivate the signal:
Select a program.
Press two of the Option Buttons
and hold until a short signal is
emitted.
[_Do
not activate/desactivate the
acoustic signal during a cycle.
Indicator
light above the
"Start/Pause"
button
e
o
The indicator light conveys the
following information:
-
Indicator light flashing red:
Program can be started.
-
Adding laundry is possible.
-
Indicator light is lit red. Program is
running.
-
Adding laundry is not possible
because the door is locked for
safety reasons.
Laundry may be added after pressing
the Start/Pause
button.
Special features
Auto Load adjust
"Auto Load adjust" adjusts the water
and energy consumption for each
program and determines the amount of
laundry and type of fabrics.
16
Publicidad
Capítulos
Tabla de contenido
