Installation Instructions - DSC neo Power Serie Manual De Referencia

Installation Instructions

These instructions must be used with the appropriate
control panel installation manual with which this
equipment is intended to be used. Operating instruc-
tions shall be made available to the user.
The HS2LCDWF wireless keypad is compatible
with wireless transceivers HSM2HOST and HS2LC-
DRF keypads.
Specifications
• Temperature range: -10°C to +55°C (14°F to
131°F) UL/ULC: 0°C to +49°C (32°F to 120°F)
• Humidity (MAX): 93%R.H. non-condensing
• Plastic enclosure protection degree: IP30, IK04
• Power adaptor output voltage: 9.0V
Models - US/Latin America: HK-XX11-U09N
(UL), Canada: HK-XX11-U09NC (ULC), EU:
HK-XX11-U09EU, UK: HK-XX11-U09NGB,
AUS./NZ, China: HK-XX11-U09NAU limited
power supply, acceptable to the authority having
jurisdiction.
NOTE: Restraints are in place for UL installations.
NOTE: This product is not to be connected to a
receptacle that is controlled by a switch.
• Battery. 4 AA, 1.5V, Energizer alkaline con-
sumer-grade (E91)
• Low Battery Indication: 4.5V
• HS2LCDWF current draw: 30mA(min)/
100mA(max)
• Wall-mount tamper (connected when installed in
UL commercial applications
• 5 programmable function keys
• Ready (Green LED), Armed (Red LED), Trou-
ble/RF Jam (Red/Yellow LED), AC (Green LED)
• Frequency: 433MHz (Brazil, China, Aus.(CE),
NZ (NA), South Africa (ICASA), MEA, India
(WPC)
• Frequency: 868MHz (EN + Local, MEA (CE))
• Frequency: 912 - 919MHz (NA/LATAM, Argen-
tina)
NOTE: For UL commercial installations, the tamper
switches are enabled.
Unpack
The HS2LCDWF keypad package is available in
three configurations
The keypad contains patented technology for the
Proximity (Prox) Tag.
HS2LCDWF - wall
mount
• 1 HS2LCDWF wall
bracket
• 1 installation manual
• 1 inner door sticker
• 4 AA batteries
• 1 hardware pack
@ 1.25A.
DC
HS2LCDWFPV - prox tag
w/ verbal annunciation
• 1 HS2LCDWF wall
bracket
• 1 installation manual
• 1 inner door sticker
• 4 AA batteries
• 1 hardware pack
• 1 prox tag
Mount
Mount the keypad where it is accessible from desig-
nated points of entry and exit. Once a dry and secure
location has been selected, perform the following
steps to mount the keypad.
.
HS2LCDWFP - prox tag
• 1 HS2LCDWF wall
bracket
• 1 installation manual
• 1 inner door sticker
• 4 AA batteries
• 1 hardware pack
• 1 prox tag
Wall Mounting Plate
1. Locate the screw holes (4) at each corner of the
mounting plate.
2. Use the four screws provided to affix the mount-
ing plate to the wall; ensure the mounting tabs
are facing you (see following diagram). If the
keypad is to be mounted on drywall, use plastic
anchors.
3. Once the batteries are installed, align the four
mounting slots in the HS2LCDWF housing with
the four mounting tabs protruding from the
mounting plate.
4. Firmly but carefully snap the keypad down onto
the mounting plate.
Mounting tab
Mounting tab
Screw hole
Mounting tab
Screw hole
Desk Stand -
HS2LCDWFDMK
(Optional)
1. Insert the four rub-
ber feet (found in
the hardware pack)
into the indentations
provided in the bot-
tom of the desk
stand.
2. Place the desk stand on a secure, uncluttered sur-
face.
3.Align the four mounting slots in the HS2LCDWF
housing with the four mounting tabs protruding
from the desk stand.
4. Slide the keypad into place. Firmly but carefully
snap the keypad down onto the desk stand.
5. To fasten the keypad securely onto the desk
stand, locate the hole in the center of the bottom
of the desk stand. Using the screws provided,
screw the keypad to the desk stand.
Screw hole
Mounting tab
Screw hole