How To Clean; Before You Begin; After Cleaning - Hoover SteamVac Dual V Manual Del Usuario

3. How to clean

Before you begin

cleaning
a. Vacuum thoroughly - For carpet,
use a HOOVER vacuum cleaner with an
agitator for best results. Vacuum uphol-
stery with a vacuum cleaner with clean-
ing tool attachments. Use a crevice tool
to reach into tufts and folds. Do not use
the 'SteamVac' deep cleaner as a dry
vacuum cleaner.
b. For upholstery, check cleaning
code - Use your HOOVER 'SteamVac'
deep cleaner only if the upholstery
fabric is marked with a "W" (for "wet"
clean) or "S/W" (for "solvent/dry" or
"wet" clean). Do not clean fabric
marked "S" ("solvent/dry" clean
only). If your upholstery does not have
a code, seek professional assistance.
c. Test for colorfastness - Wet a white
absorbent cloth with the detergent. In a
small, hidden area, gently rub the surface
with the dampened cloth. Wait ten minutes
and check for color removal or bleed with
white paper towel or cloth. If surface has
more than one color, check all colors.

After cleaning

a. Allow carpet or upholstery to dry. To
help prevent matting and resoiling the
carpet, keep children and pets away
from surface until it is completely dry. If
it is necessary to walk on damp car-
pet, place towels or white cloths on the
traffic areas.
If furniture must be replaced before the
carpet is dry, place plastic or aluminum
foil under legs of furniture so metal
slides or wood finishes will not stain the
carpet.
b. Empty tanks, rinse with clear water
and let air dry. Rinse the recovery tank
lid and let air dry.
Any unused detergent may be left in
the detergent container for future use.
10
d. When cleaning entire floor, move
furniture out of area to be cleaned
(may not be necessary if only high traf-
fic areas are to be cleaned). For furni-
ture too heavy to move, place aluminum
foil or wax paper under legs. This will
prevent wood finishes from staining car-
pet. Pin up furniture skirts and
draperies.
e. Pretreat spots and heavy traffic
areas with HOOVER Spot & Stain
®
Spray Cleaner*- Test Spot & Stain
Spray Cleaner for colorfastness by first
spraying it on a hidden area; wait ten
minutes and blot with white paper
towels or cloth.
If no color change is visible, spray Spot &
Stain Spray Cleaner onto spots and traffic
areas. Wait at least ten minutes. Use your
'SteamVac' deep cleaner to pick up Spot &
Stain Spray Cleaner and spot. Repeat until
spot is removed; carefully scrub with a
household scrub brush if necessary.
Do not saturate carpet or upholstery with
Spot & Stain Spray Cleaner.
No cleaning solution removes all stains
from all carpets. Stain removal varies with
the type of spill, time elapsed before
removal, carpet material, and carpet type.
3-1
c. Remove lint from filter screen located
inside recovery tank.
f. To prevent staining, use plastic or alu-
minum foil to protect wood or metal sur-
faces from possible water spray.
g. To avoid wetting and possible damage
to wood floors underneath area rugs/car-
pet, either move area rugs/ carpet to a non-
wood bare floor surface or place waterproof
material (e.g. plastic) underneath them
before cleaning.
See pages 10-14 for instructions on various
cleaning tasks.
*Available at additional cost if not included
with your model.
3-2
d. Remove lint from filter screen located
on bottom of cleaner as follows.
Note: When brushes seem to be rotat-
ing slowly, disconnect deep cleaner
from electical outlet and check and
clean this screen.
Remove both tanks as described in
Figs. 2-10 and 2-21. Tilt cleaner back so
handle rests on floor.
Squeeze filter frame, lift and pull it out.
Wipe off screen and push frame back
into place.
Return cleaner to upright position.
e. If desired, vacuum thoroughly after
carpet has completely dried. This will
help reduce any shading left by the
deep cleaner's brushes.