Replacement Headshell - IMG STAGELINE DJP-200USB Manual De Instrucciones

6 Operation
1) Remove the protective cap from the stylus.
2) Switch on the turntable with the POWER
switch (4). If the switch AUTO STOP (5) is set
to OFF, the turntable will start rotating after
switching on.
To start and stop the rotation of the
turntable by the tone arm (13), set the switch
AUTO STOP to ON.
3) Select the speed with the button 33
45 (17):
RPM
Long-playing records: disengage the button =
1
33 ⁄
RPM
3
Single records: engage the button = 45
4) Put on the record. For single records use the
adapter (1). It is easy to remove the adapter
from its recess: simply press its rear edge.
5) Open the lock (12) for the tone arm (13) to the
right. To lift the tone arm, set the lever (11) for
the tone arm to the rear position .
6) Seize the handle (16) of the tone arm and
position the stylus above the beginning or the
desired spot of the record. Set the lever (11)
for lifting the tone arm to the front position .
The tone arm is slowly lowered onto the
record.
7) To stop playing, lift the tone arm with the lever
(11) and return it to its support with your
hand.
8) After use, secure the tone arm with the lock
(12) and switch off the turntable with the
POWER switch (4).
7 Accessories
7.1 Replacement phono cartridge
system and replacement stylus
The phono cartridge system or the stylus is eas-
ily replaced, if required. The corresponding re -
placement parts are available from your retailer,
e. g. the magnetic phono cartridge system EN-24
and the matching replacement stylus EN-24SP
from MONACOR.
1) To replace the stylus, remove the orange
support of the stylus to the front. Put the new
stylus on the phono cartridge system.
2) To replace the phono cartridge system,
unscrew the cap nut (14) and remove the
headshell (15) from the tone arm (13).
3) Unscrew the phono cartridge system from the
support and remove the connecting wires.
4) Screw the new phono cartridge system onto
the support and connect the wires as follows:
blue left channel, positive pole
white left channel, negative pole
green right channel, positive pole
red right channel, negative pole
5) After replacing the phono cartridge system,
readjust the counterweight and the anti-skat-
ing value ( chapters 4.3 and 4.4).
/
RPM

7.2 Replacement headshell

A replacement headshell (e. g. the headshell
EN-120 from MONACOR) including a phono
cartridge system allows for quick replacement, if
RPM
necessary. For storage, you may put the re -
placement headshell on the support (8).
To replace the headshell (15), simply screw it
off and the new one on. Then readjust the coun-
terweight and the anti-skating value (
ters 4.3 and 4.4).
8 Maintenance
8.1 Cleaning
Clean the turntable housing with a soft cloth, dry
or slightly damp (not dripping wet). Never use
alcohol, chemicals or aggressive detergents! To
dust the stylus and the records, the correspond -
ing accessories are available from your retailer,
e. g. the carbon fibre record cleaning brush
DC-100 from MONACOR.
8.2 Transport
When dispatching the turntable, make sure to
wrap the turntable and its components in their
original packaging or to particularly secure them
for transport. Any damage due to careless trans-
port of the turntable (e. g. platter not removed
from the axle and not secured or similar negli-
gence) will not be covered by the guarantee.
Therefore, any resulting repairs will be charged!
When dispatching the turntable, always observe
the following precautions:
1) Put the protective cap on the stylus.
2) Secure the tone arm (13) with the lock (11).
3) Unscrew the counterweight (9) for the tone
arm.
4) Remove the turntable platter from the axle,
wrap it separately and secure it against slip-
ping.
5) It is recommended to use the original card-
board box of the turntable.
All rights reserved by MONACOR
manual may be reproduced in any form or by any means for any commercial use.
9 Specifications
Phono cartridge system . . magnetic
Turntable platter: . . . . . . . . ∅ 332 mm,
Drive: . . . . . . . . . . . . . . . . belt drive
Speeds: . . . . . . . . . . . . . . . 33
Starting torque: . . . . . . . . . 0.03 Nm
Wow and flutter: . . . . . . . . < 0.3 %
Output: . . . . . . . . . . . . . . . line level,
Power supply: . . . . . . . . . . 230 V~ / 50 Hz
Power consumption: . . . . . 20 VA max.
Ambient temperature: . . . . 0 – 40 °C
chap-
Dimensions (W × H × D): . 450 × 152 × 352 mm
Weight: . . . . . . . . . . . . . . . 3.2 kg
Subject to technical modification.
® INTERNATIONAL GmbH & Co. KG. No part of this instruction
GB
(moving magnet)
cast aluminium
1
⁄ and
RPM
3
45
RPM
connection cable
with RCA plug
7