Plumbing; Preparation; Anti-Tip Bracket - Sub-Zero ICBIC-18FI Guia De Instalacion

SITE PREPARATION

Plumbing

Installation must comply with all applicable plumbing codes.
The water supply line should be located within the shaded
area shown in the illustrations below. The water supply line
should be connected to the house supply with an easily
accessible shut-off valve. Do not use self-piercing valves.
The water supply line must be flush to the floor and not
interfere with installation of the anti-tip bracket.
An in-line filter is required for models with an ice maker or
water dispenser when water conditions have a high sedi-
ment content.
A reverse osmosis system can be used provided there
is constant water pressure of 2.4–8.3 bar supplied to the
unit at all times. A copper line is not recommended for this
application.
PLUMBING REQUIREMENTS
1
Water Supply Line / " OD copper, braided
4
stainless steel or PEX tubing
Water Pressure 2.4–8.3 bar
Excess Water Line for Connection
WATER SUPPLY LOCATION
WIDTH
457 mm Models
610 mm Models
762 mm Models
914 mm Models
RIGHT SIDE RIGHT SIDE
A
OF OPENING OF OPENING
BACK WALL BACK WALL
A 152 A 152
WATER WATER RIGHT
mm mm
LINE LINE SIDE OF
OPENING
76 mm 76 mm
FLOOR FLOOR
FRONT VIEW FRONT VIEW TOP VIEW TOP VIEW
Water supply location (rear). Water supply location (bottom).
|
4 English

Preparation

Uncrate the unit and inspect for damage. Remove the wood
base and discard shipping bolts and brackets. Remove and
recycle packing materials. Do not discard the kickplate, anti-
tip bracket and hardware.
Remove the kickplate by extracting the two mounting
screws. Refer to the illustration below.
SCREW
.9 m
Kickplate removal.
A
76 mm
140 mm
152 mm
229 mm
13 mm 13 mm
A
152 152
mm mm
RIGHT
SIDE OF
OPENING

Anti-Tip Bracket

WARNING
To prevent the unit from tipping forward, the anti-tip
bracket must be installed.
The back of the anti-tip bracket must be installed 610 mm
from the front of the unit (without panels).
Use all anti-tip bracket hardware as instructed for wood or
concrete floors.
IMPORTANT NOTE: For wood or concrete floor applications,
if the #12 screws do not hit a wall stud or wall plate, use the
#8 screws and #12 washers with the wall anchors.
In some installations the subflooring or
IMPORTANT NOTE:
finished floor may necessitate angling the screws used to
fasten the anti-tip bracket to the back wall.
ANTI-TIP HARDWARE
1 Anti-tip bracket
12 #12 x 64 mm pan head screws
3
4 / "–16 x 95 mm wedge anchors
8
12 #12 flat washers
4 #8–18 x 32 mm truss head screws
4 Nylon Zip-it ® wall anchors
WOOD FLOOR APPLICATION
After properly locating the anti-tip bracket in the opening,
drill pilot holes 5 mm diameter maximum in the wall studs or
wall plate. Use the #12 screws and washers to secure the
brackets. Verify the screws penetrate through the flooring
material and into wall studs or wall plate a minimum of 19
mm. Refer to the illustration and chart below.
CONCRETE FLOOR APPLICATION
After properly locating the anti-tip bracket in the opening,
drill pilot holes 5 mm diameter maximum in the wall studs
or wall plate. Drill 10 mm diameter holes into the concrete a
minimum of 38 mm deep. Use the #12 screws and washers
to secure the brackets to the wall, and use the 3 / " wedge
8
anchors to secure the brackets to the floor. Verify the screws
penetrate wall studs or wall plate a minimum of 19 mm.
Refer to the illustration and chart below.
ANTI-TIP BRACKET PLACEMENT
WIDTH
457 mm Models
610 mm Models
762 mm Models
914 mm Models
A
A
A A
FINISHED FINISHED
FLOORING FLOORING
WALL PLATE WALL PLATE
SUBFLOORING SUBFLOORING
38 mm
WOOD FLOOR CONCRETE
min
FLOOR
Wood floor. Concrete floor.
A
229 mm
305 mm
318 mm
457 mm