Adjustment Of Cutting Height; Adjustment For An Appropriate Height; Safety Precautions - Makita ELM4610 Manual De Instrucciones

Model:
Grass catcher:
Net weight:
Degree of protection against liquid:
Height adjustment:
The difference between ELM4610 and ELM4611 is ELM4611 with self propel system, ELM4610 does not have.
5. ASSEMBLY
5-1 ASSEMBLY THE FOLDING HANDLE
A) Fix the lower handlebars into the unit body with
locking knobs. (Fig. 2 - 5)
B) Release the upper handlebars for folding. Connect the
upper handle and the lower handle with the locking
knob. (Fig. 6 & 7)
C) Position all cables over the handle shafts. Clamp them
around the middle of lower handles by the cable
clamps so that the cables are fixed on the outside of
the machine. Otherwise the cables may be pinched by
opening/closing the rear cover or forced by folding the
upper handle. (Fig. 8)
5-2 ASSEMBLY THE GRASS CATCHER
1. To fit: Raise the rear cover and hitch the grass catcher
on rear of mower. (Fig. 9 & 10)
2. To remove: Grasp and lift the rear cover, remove grass
catcher.
6. ADJUSTMENT OF CUTTING
HEIGHT
Apply outward pressure to disengage lever from rack.
Move lover forward or back to adjust height.
The height (the blade to the ground) can be adjusted from
20 mm (the lowest position) to 75 mm (the highest
position), 5 height positions (20 mm/32 mm/44 mm/
60 mm/75 mm). (Fig. 11)
WARNING: Make this adjustment only when the
blade is stopped.
7. ADJUSTMENT FOR AN
APPROPRIATE HEIGHT
1) Back out the locking knob which fixed the lower
handle, refer to Fig. 12.
2) Refer to Fig. 13, move the lower handle up and down,
adjust it to the proper height.
There is 3 adjusting height to be choose on this type
lawn mower; at 1 height, lower handle to the ground is
highest., 3 height is the lowest.
3) Adjusting to the proper height, then fix the lower
handle by the locking knobs.
WARNING: The left side and right side of lower
handle must adjust to the same height.
ELM4610
60 L
29.0 kg
IPX4
20-75 mm, 5 adjustment
8. MULCHING MOWER
What is mulching?
When mulching, the grass is cut in one working step, then
finely chopped and returned to the grass strip as natural
fertilizer.
Hints for mulch-mowing:
- Regular cut-back by max. 2 cm form 6 cm to 4 cm
grass height.
- Use a sharp cutting knife
- Do not mow wet grass.
- Set max. Motor speed.
- Only move the working pace.
- Regularly clean mulching wedge, housing inner side
and mowing blade.
WARNING: Only with a stopped motor and
standstill cutter.
1. Raise the rear cover and remove the grass catcher.
2. Push the mulching wedge into the deck. Lock the
mulching wedge with the button into the opening on
the deck. (Fig. 14 & 15)
3. Lower the rear cover again.

9. SAFETY PRECAUTIONS

a) Always operate with the deflector or grass catcher in
the correct position.
b) Always stop the motor before removing the grass
catcher or adjusting the height of cutting position.
1) Before mowing, remove all foreign objects from the
lawn which may be thrown by the machine. While
mowing, stay alert for any foreign objects which may
have been missed. (Fig. 16)
2) Never lift the rear of the mower while starting the
motor or during normal operation. (Fig. 17)
3) Always ensure that the ventilation openings are kept
clear of debris.
4) Never place your hands or feet underneath the
underpan or into the rear discharge chute while the
motor is running. (Fig. 18)
10. STARTING
Before connecting up the lawn mower to the electric
power supply, make sure that the mains supply voltage is
230 V – 50 Hz. When the lawn mower power on, the
indicator light will turn on (Fig. 19).
Fig 20 A for ELM4610:
a) Press the safety push-button (1).
b) And meanwhile, pull the switch handle (2), and keep it
in grasp.
ELM4611
60 L
32.1 kg
IPX4
20-75 mm, 5 adjustment
9