Monacor PA-1130CD Manual De Instrucciones página 10

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 29
GB
4 Installation of the Insertion Module
WARNING Prior to the installation of the insertion
disconnect the mains plug of the ampli-
fier or of the basic insertion unit from the
mains socket. Otherwise there is an
electric shock hazard.
1) Remove the housing cover of the amplifier or of the
basic unit.
2) Screw off the cover for the insertion compartment
on the front side of the amplifier or of the basic unit.
Install the insertion and tighten it with screws.
3) Connect the bare three-pole line of the amplifier or
of the basic unit to the pin housing of position c (see
fig. 3). This allows to supply the insertion with 17 V
and to feed the audio signal to the amplifier.
4) If required, two further audio outputs are available:
balanced mono output at the connection d
unbalanced stereo output at the connection e
The installation is terminated for the insertion
PA-1130CD. Close the amplifier or the basic unit with
the housing cover.
Make the following operational steps additionally
for the insertion PA-1130RCD:
5) Remove the cover (fig. 4) on the rear side of the
amplifier or of the basic unit. Insert the supplied
antenna PCB there and tighten it with screws.
6) Connect the line of the inserted antenna PCB to the
five-pole pin housing of position a.
7) The insertion PA-1130RCD has a storage battery
so that the stations also remain stored with the unit
switched off. The storage battery is deactivated in
the factory to prevent successive discharge before
installation. To activate the battery, set the jumper b
to position ON.
To deactivate the battery again (e. g. if stored for
a longer time), set the jumper b to position OFF
again.
8) Close the amplifier or the basic unit with the hous-
ing cover and connect the reception antennas to the
screw connections of the antennas. Pay attention to
the lettering on the amplifier or on the basic unit:
AM+GND for medium wave antenna
FM 75 Ω
for FM antenna with 75 Ω connection
cable
300 Ω
for FM antenna with 300 Ω connection
cable
10
5 Operation
1) Switch on the amplifier or the basic unit with the
mains switch and the insertion module with the
POWER button (11). The red POWER LED (1) and
the display (14) light up.
2) Adjust the desired volume with the volume control
LEVEL (18).
3) To switch off, press the POWER button again.
5.1 Operation of the CD player
It is possible to play standard audio CDs on the
CD player, including those you have burnt yourself
(CD-R). The replay of CDs with compressed audio
files (made with the current standard compression pro-
cedure) is also possible. In case of rewritable CDs
(CD-RW), however, problems may occur while replay-
ing depending on the CD type, the CD burner and the
burning programme used.
5.1.1 Replaying a CD
1) Insert a CD with the lettering facing upwards so far
into the slot (6) until it is automatically retracted. If
there is already a CD in the unit, the display shows
the symbol
.
2) To change a CD, press the button EJECT (13). The
CD is ejected.
Model PA-1130RCD switches to radio reception
and retracts the CD after 10 seconds if it is not
removed.
3) After loading, the first title starts. For standard
audio CDs the display shows the title number and
the time already played (min. : sec.), see fig. 2.
For CDs with compressed audio files, the file
name passes through the display and, after pass-
ing through of the file name, the title number behind
the letter "T". By pressing the button DISP (17) sev-
eral times, information about the title of the music
piece, album, artist, etc. (ID3 tags) can be dis-
played. If no ID3 tags are available, the display
shows NO ID3.
Note: For model PA-1130RCD, by pressing the
button DISP, information on the station tuned is dis-
played also during CD replay, see chapter 5.2.3,
paragraph information. Therefore, press the button
DISP so many times until the desired information is
displayed.
4) At the end of a CD the CD player starts again with
the first title (continuous replay).
5) To interrupt the CD replay, press the button
The display shows S-PAUSE.
Press the button
replay.
(7).
again to continue the CD

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Pa-1130rcd

Tabla de contenido