Setting Into Operation - Monacor TVCCD-160S Manual De Instrucciones

1 1
( / – / s). Due to the one-cable technique, to
50 100 000
connect camera and power supply unit only one coax-
ial cable is necessary by which the power supply and
the video signal are transferred in common.
The camera is weatherproof (IP 68) and can also
be used for outside applications. The power supply
unit must in any case be used indoors.
4 Mounting
1) Mount the supplied bracket [or, if necessary, an -
other bracket with 6.3 mm (
desired place.
2) Loosen the lower knurled nut (8) of the bracket so
that the thread bolt (5) can freely be moved and
screwed into one of the two thread jacks (3) of the
camera by means of the upper knurled nut (6). If
the picture reproduction is inverted after setting the
camera into operation, the other thread jack must
be used. Due to the cylindrical form of the camera it
is not possible to see before which way round the
camera has to be mounted.
3) Align the camera coarsely and fix it by tightening the
lower knurled nut (8). An exact alignment can only
be made after setting the camera into operation.

5 Setting into operation

1) Connect the cable of the camera (4) to jack TO
CAMERA (15) of the power supply unit. The length
of the cable is 30 m. It can be extended up to 500 m
by using a high-quality cable:
Cable Type Max. Cable Length
RG-58U
RG-59U
RG-6U
Up to 350 m the cable VCC-59 by MONACOR is
also suitable.
2) Connect the video output VIDEO OUT TO MONI-
TOR (14) of the power supply unit via a 75 Ω coax-
ial cable to the video input jack of the monitor or a
camera switcher resp. video splitter. Observe the
correct 75 Ω termination.
3) Plug the mains plug into a socket (230 V~/50 Hz)
and switch on the power supply unit with the
POWER switch (10). The POWER LED (9) lights.
4) Switch on the connected monitor as well and align
the camera exactly to the monitoring range. If the
picture reproduction is inverted, mount the camera
by turning it 180°.
All rights reserved by MONACOR
be reproduced in any form or by any means for any commercial use.
1
⁄ ")] thread at the
4
200 m
350 m
500 m
INTERNATIONAL GmbH & Co. KG. No part of this instruction manual may
®
5) Screw off the screw sleeve (2) of the camera, and
adjust a clear picture by turning the lens (1).
Tighten the screw sleeve again.
6) With the four sliding switches VIDEO GAIN ADJ. (13)
on the rear side of the power supply unit it is possible
to change the video output level, if required (see the
following table). Thus, level losses due to a long con-
nection cable between the camera and the supply
unit can be compensated.
Switch position
VIDEO GAIN ADJ.
or
or
6 Specifications
Image sensor: . . . . . . . . . 8.5 mm (
Synchronization: . . . . . . . hor. 15 625 Hz, vert. 50 Hz
Number of pixels: . . . . . . . hor. 500 × vert. 582
Resolution: . . . . . . . . . . . . 420 lines
Lens: . . . . . . . . . . . . . . . . 1: 2.0/3.6 mm
Minimum illumination: . . . 0.01 Lux
S/N ratio: . . . . . . . . . . . . . > 50 dB
Video output: . . . . . . . . . . 1 Vpp/75 Ω
Admissible
ambient temperature: . . . -10 °C to +50 °C
Power supply: . . . . . . . . . 230 V~/50 Hz/5 VA
Dimensions
camera: . . . . . . . . . . . . ∅ 28 mm × 122 mm
power supply unit: . . . . 106 × 44 × 96 mm
Weight
camera: . . . . . . . . . . . . 115 g
power supply unit: . . . . 600 g
Subject to technical modification.
Output level
without cable losses
1.2 Vpp
1.3 Vpp
1.4 Vpp
1.1 Vpp
1.0 Vpp
1
⁄ ") CCD chip
3
GB
7