Replacing The Power Cable; Cleaning, Maintenance And Ordering Of Spare Parts; Carbon Brushes - EINHELL RG-SA 1433 Manual De Instrucciones Original

remove soil and grass build-up. Deposits make it
more diffi cult to start the aerator and decrease the
quality of the scarifying.
Always scarify along inclines (not up and down).
Switch off the motor before doing any checks on
the roller.
Danger!
The roller rotates for a few seconds after the
motor is switched off . Never attempt to stop the
roller. In the event that the rotating roller strikes
an object, immediately switch off the equipment
and wait for the roller to come to a complete stop.
Then inspect the condition of the roller. Replace
any parts that are damaged (see section 8.4).
Lay the power cable on the ground in loops in
front of the power outlet. Scarify away from the
power outlet and cable, making sure that the
power cable always trails in the already scarifi ed
grass so that the equipment does not travel over
the cable.

7. Replacing the power cable

Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
8. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the mains power plug before star-
ting any cleaning work.
8.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
Anl_RG-SA_1433_SPK9.indb 24 Anl_RG-SA_1433_SPK9.indb 24
GB
the risk of an electric shock.

8.2 Carbon brushes

In case of excessive sparking, have the carbon
brushes checked only by a qualifi ed electrician.
Danger! The carbon brushes should not be rep
laced by anyone but a qualifi ed electrician.
8.3 Maintenance
•
A worn out or damaged cutting unit should be
replaced by an authorised expert (see adress
on the warranty certificate).
•
Take care that all fastening elements (screws,
nuts, etc.) are firmly tightened, so that you
can work safely with the scarifier.
•
Store the scarifier in a dry place.
•
For longer life, all screw-fastened parts, such
as wheels and axles should be cleaned and
subsequently oiled.
•
Regular servicing of the scarifier not only
secures longer endurance and performance,
but also contributes to an accurate and simp-
le scarification of your lawn.
•
At the end of the season, carry out a general
check of the scarifier, and remove all residue
collected. Before the start of every season, it
is absolutely necessary to check the state of
the scarifier. Contact our Customer Service
(see address on the warranty certificate) if
repair work is necessary.
To save storage space, the push bar has a P and
an A position. (Fig. 17).
•
In the P-position, the scarifier can be stored in
a corner, to save space (Fig. 18).
•
In the A-position, the scarifier can be hung
(as shown in Fig 19) on the wall mount inclu-
ded, to save space.
8.4 Changing the roller (see Figures 20-23)
Caution! Be sure to wear work gloves!
Only replace the roller with a genuine Einhell rol-
ler, as this will ensure top performance and safety
under all conditions.
Remove the two hexagon socket screws (Fig. 20
/ Item 18). Lift the roller on this side and pull out in
the direction of the arrow (Fig. 21).
Now slide the new roller in the direction of the ar-
row (Fig. 23) onto the square-ended drive (Fig. 22
/ Item 17) and press into the holder (Fig. 23).
Refasten the roller with the two hexagon socket
screws (Fig. 20 / Item 18).
- 24 -
27.04.2020 06:50:18 27.04.2020 06:50:18