Clearing Blockages; Cleaning, Maintenance And Ordering Spare Parts - EINHELL GE-CL 36/230 Li E Manual De Instrucciones Original

•
Set the desired blowing velocity with the
speed controller (see section 6.5).
•
Channel the air stream forward and walk
slowly to blow foliage or garden refuse into a
pile or to clear out hard-to-reach places.
•
To increase the blowing velocity for a short
time, press the "Turbo button" (see section
6.6).
Danger!
Never gather (blow) hot, combustible or explosive
materials into piles.
6.3.2 Sucking up foliage
Caution!
•
Only use the leaf blower vac in vacuum mode
if the catch bag is undamaged and properly
fitted.
•
Do not pick up too many leaves in one go as
this could clog the tube and the shredder.
•
To clear any blockages, follow the steps de-
scribed in the section "Clearing blockages".
•
Do not pick up hard or damp materials.
•
Fit the prepared 2-piece suction tube with rol-
lers and carry-handle, harness and catch bag
(see section 5.3) to the motor housing.
•
Check that all the components are correctly
fastened (see section 5.4).
•
Always position the suction tube on the
ground and adjust the length of the strap to
your requirements (see section 6.1). The gui-
de rollers (Fig. 1/Item 9) at the bottom end of
the suction tube will help you to maneuver the
suction tube on the ground.
•
Turn on the equipment (see section 6.2).
•
Set the desired suction power with the speed
controller (see section 6.5).
•
To increase the suction power for a short
time, press the "Turbo button" (see section
6.6).
6.4 Emptying the catch bag (Fig. 1b)
Empty the catch bag (7) in good time. With a
nearly full bag, the suction power drops notably.
Organic waste should be composted.
•
Switch off the equipment and remove the bat-
teries.
•
Open the zipper on the catch bag (7) and
shake out the material.
•
Close the zip on the catch bag (7) again.
Anl_GE_CL_36_230_Li_E_Solo_SPK9.indb 23 Anl_GE_CL_36_230_Li_E_Solo_SPK9.indb 23
GB
6.5 Speed control (Fig. 10)
The equipment is fi tted with a variable speed
trigger. To use it, turn the speed controller (Item
10) to the desired position. Use the device only
with the speed which is actually required and
do not let it run at a speed which is faster than
necessary.
1 = Minimum speed
MAX = Maximum speed
6.6 Turbo mode (Fig. 11)
If you need higher blowing power or suction pow-
er for a short time, you can press the turbo button
(Item T). Pressing the turbo button increases the
speed for a short time and with it the blowing or
suction power.
Important: Never press the turbo button for
any longer than necessary, in order to keep
the noise level down and extend the battery
operating time.

6.7 Clearing blockages

Danger!
•
Switch off the equipment, wait for the moving
parts to come to a standstill and remove the
batteries.
•
Wear protective gloves
•
Use suitable tools (e.g. a wooden stick)
1. Examine the tube for blockages. Tap the suc-
tion tube carefully or use a wooden stick to
clear any blockages.
2. Empty the catch bag and remove it. Remove
the suction tube.
3. Examine the openings in the motor housing
for possible blockages. Remove the blockage
with a stick if necessary. Make sure that the
shredder is clear.
7. Cleaning, maintenance and
ordering spare parts
Hazard!
Always remove the batteries before starting any
cleaning work.
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
- 23 -
17.12.2019 14:38:10 17.12.2019 14:38:10