Basic Operation; Selecting Inputs; Usb/Ipod Operation; Ipod/Iphone Connection - Rotel RAP-1580 Manual De Instrucciones

NOTE: Not all surround modes are available for all surround source
formats. The input source signal will determine the available surround
options that can be selected.

Basic Operation

This section covers the basic operating controls of the RAP-1580 and the
remote control.

Selecting Inputs

You can select any of the source inputs for listening and/or watching: VIDEO
1 - 8, CD, PHONO, XLR, MULTI INPUT, USB, PC-USB, BLUETOOTH or TUNER.
The source inputs can be customized using the INPUT SETUP menu to assign
which HDMI input to use as the video source. Video 1- 8 inputs can also
be configured to accept any analog and digital audio sources. The default
of audio source is set to HDMI Audio.
When you have configured the source input, you can use the INPUT buttons
to select the desired inputs:
1. Press the INPUT buttons on the front panel
buttons to switch to the selected source input i.e. CD, Tuner, Video 1
etc. then press ENTER.
2. Press the source input button on the remote control
desired source.

USB/iPod Operation

iPod/iPhone Connection

0
1. An iPod/iPhone can be connected using the proper USB cable to the
USB front socket of the RAP-1580.
2. The iPod/iPhone will stream a digital music signal to the unit. Music
selection and playback control can be made from the iPod/iPhone.
3. The iPod/iPhone screen will remain active while connected to the unit.
Playback Control Buttons
L
Transport controls are available from the remote control during playback
including play, stop/pause, next track, previous track.

Bluetooth

Bluetooth Connection

The Bluetooth feature allows you to stream music wireless from your Bluetooth
enabled device, i.e. mobile phones. Select the BLUETOOTH (BT) input on
the RAP-1580. From your device (mobile phones etc.) activate Bluetooth and
allow it to search for other Bluetooth devices. Select "Rotel Bluetooth" and
connect to it. Once connected you can start streaming music to the RAP-1580.
NOTE: The RAP-1580 Bluetooth is APTX compatible. This enables you
to stream music at lossless CD quality.
NOTE: Some Bluetooth devices may require you to establish connection
again with the RAP-1580 if the unit was powered off. If this occurs,
please go through the above steps to re-connect.
6
and use the navigation
M to select the

Rear PC-USB

Rear PC-USB Connection

The rear USB socket labeled PC-USB accepts a type B USB plug. This input
accepts PCM audio signals sent from your computer up to 24 bits/192kHz
resolution.

Setup

The Rotel RAP-1580 features two types of information displays to help
operate the system. The first consists of simple status displays that appear on
the TV screen whenever primary settings (Volume, Input, etc.) are changed.
NOTE: On screen status displays are only available on HDMI inputs
4 to 8.
A more comprehensive ON-SCREEN DISPLAY (OSD) menu system is available
at any time, for all inputs, by pressing the SETUP
7
or the MENU button on the front panel. These OSD menus guide you
through the configuration and setup of the RAP-1580. The settings made in
the configuration process are memorized as default settings and need not
be made again for normal operation of the unit.
The OSD menus can be configured to display several different languages.
The default English versions of all main menus are shown at the front of this
manual. If your language is available, those menus will be shown in the
instructions. If you would like to change from the default English language
before proceeding, go to the instructions for the SYSTEM SETUP menu later
in this manual. From this menu, you can change the language display.

Menu Basics

Navigation Buttons

The following remote control buttons are used to navigate the OSD menu
system:
SETUP button: Press to display the MAIN MENU. If a menu is already
visible, push this button to close the OSD and return to normal operation.
Up/Down buttons: Press to move up and down in the lists of menu items
that appear on the OSD screens.
Left/Right buttons: Press to change the current settings for a selected menu
item on OSD screens.
ENTER button: Press ENTER to confirm a setting.
BACK Button: Press BACK to go back to the previous menu.
21
H button on the remote