Before Starting The Equipment; Fitting The Battery - EINHELL CE-CP 18/180 Li E Manual De Instrucciones Original

anti-vibration handles securely to the machi-
ne body.
If you experience an unpleasant feeling or skin
discoloration on your hands while using the ma-
chine, stop your work immediately. Take adequate
breaks from your work. If you do not take ade-
quate breaks from your work, you could develop
hand-arm vibration syndrome.
You should evaluate the level of strain in relation
to the work involved and the use of the machine
and take adequate work breaks accordingly. This
will enable you to signifi cantly reduce the level
of strain over the whole period of work. Minimize
the risk to which you are exposed from vibrations.
Look after this machine with care in accordance
with the operating instructions.
If the machine is deployed or used often, you
should consult your dealer and possibly consider
obtaining anti-vibration accessories (handles).
Do not use the machine at temperatures of
t=10°C or lower. Think out a work plan which ena-
bles you to limit your exposure to vibrations.
A certain level of noise nuisance is inevitable with
this equipment. Carry out noise-intensive jobs
at times that are acceptable and allowed. Where
applicable, observe rest periods and restrict your
working time to a minimum. Suitable ear protec-
tion must be worn for your own safety and for the
safety of others nearby.

5. Before starting the equipment

Only press the spindle lock when the equipment
is at a standstill.
5.1 Assembling the equipment (Fig. 4-6)
Important! Remove the rechargeable battery be-
fore starting the assembly work.
The equipment is supplied without batteries
and without a charger.

5.2. Fitting the battery

Press the side pushlock button (c) of the battery
pack as shown in Fig. 9 and push the battery
pack into the mount provided. When the battery
is positioned as in Fig. 9, make sure that the
pushlock button latches in place! To remove the
battery pack, proceed in reverse order.
Anl_CE_CP_18_180_Li_E_Solo_SPK9.indb 21 Anl_CE_CP_18_180_Li_E_Solo_SPK9.indb 21
GB
5.3 Charging the battery (Fig. 7)
1. Take the battery pack out of the equipment.
Do this by pressing the pushlock button.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
into the socket outlet. The green LED will then
begin to fl ash.
3. Insert the battery pack (11) into the battery
charger (10).
4. In the section entitled „Charger indicator" you
will fi nd a table with an explanation of the LED
indicator on the charger.
The battery pack can become a little warm during
the charging. This is normal.
If the battery pack fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts
If the battery pack still fails to charge, send
•
the charging unit
•
and the battery pack
to our customer service center.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the equipment
drops. Never allow the battery pack to become
fully discharged. This will cause it to develop a
defect.
5.4 Battery capacity indicator (Fig. 8)
Press the button for the battery capacity indicator
(Item A). The battery capacity indicator (Item B)
shows the charge status of the battery using 3
LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED blinks:
The battery is empty, recharge the battery.
All LEDs fl ash:
The battery pack has undergone exhaustive di-
scharge and is defective. Do not use or charge a
defective battery pack.
- 21 -
03.07.2019 08:34:38 03.07.2019 08:34:38