Makita ELM4110 Manual De Instrucciones página 13

c) Push the lawn mower manually when the motor is
running. If you release the switch handle, the motor
will stop.
CAUTION: The blade starts turning as soon as
the motor is started.
WARNING: Cutting elements continue to rotate
after the motor is switch off.
CAUTION: Determine the maximum permissible
system impedance Zmax (0.330Ω) at the interface point of
the user's supply, declare Zmax (0.330Ω) in the
equipment instruction manual and instruct the user to
determine in consultation with the supply authority, if
necessary, that the equipment is connected only to a
supply of that impedance or less.
10. BLADE
The blade is made of pressed steel. It will be necessary to
reshape it frequently (with a grind wheel).
Ensure that it is always balanced (an unbalanced blade
will cause dangerous vibrations). To check for balance,
insert a round rod through the central hole and support
the blade horizontally. (Fig. 19) A balanced blade will
remain horizontal. If the blade is not balanced the heavy
end will rotate downwards. Reshape the heavy end until
the blade is currently balanced. (Fig. 20) To remove the
blade (2), unscrew the blade screw (3). (Fig. 21 - 23)
Check the conditions of the fan(1), and replace any parts,
which are damaged. (Fig. 21)
When reassembling, make sure that the cutting edges
face in the direction of the motor rotation. The blade screw
(3) must be tightened to 20 -25 Nm torque.
WARNING: For service,
replace the blade with: MAKITA
263001427 only.
11. EXTENSION CORDS
You should only use extension cords for outdoor use,
PVC or rubber cord ordinary duty with a cross sectional
area not less than 1.0 mm
Before using, check the supply and extension cords for
signs of damaged during use, disconnect the cord for
signs of damage or aging. If the cord becomes damaged
during use, disconnect the cord from the supply
immediately. DO NOT TOUCH THE CORD BEFORE
DISCONNECTING THE SUPPLY. Do not use the
appliance if the cord is damaged or worn. Keep extension
cord away from cutting elements.
2
.
12. MAINTENANCE AND CARE
WARNING: Before performing any Maintenance
or cleaning work, always pull out the mains plug!
Do not spray the unit with water. Ingress of water may
destroy the switch-plug combination unit and the electric
motor. Clean the unit with a cloth, hand brush, etc.
Never use gasoline, benzine, thinner, alcohol or the like.
Discoloration, deformation or cracks may result.
Expert inspection is required, do not make any
adjustment by yourself, must contact to Makita
authorized service centre:
a) If the lawn mower strikes an object.
b) If the motor stops suddenly.
c) If the blade is bent (do not align!).
d) If the motor shaft is bent (do not align!).
e) If a short-circuit occurs when the cable is connected.
f) If the gears are damaged.
g) If the V-belt is defective.
13. TROUBLE SHOOTING
WARNING: Before performing any maintenance
or cleaning work, always pull out the mains plug and wait
until the cutter has come to a standstill.
Fault Remedial action
Check mains connection cable.
Start on short grass or on an area which
Motor does not has already been mown.
run Clean discharge channel/housing-the
mowing blade must rotate freely.
Correct the cutting height.
Correct the cutting height.
Clean discharge channel/housing.
Motor power
Have mowing blade resharpened/
drops
replaced 
authorized service centre.
Correct the cutting height.
Allow the lawn to dry.
Have mowing blade resharpened/
Grass catcher
replaced 
is not filled
authorized service centre.
Clean the grille on the grass catcher.
Clean the discharge channel/housing.
CAUTION: Faults which cannot be rectified with
the aid of this table may be rectified by Makita authorized
service centre only.
14. ENVIRONMENTALLY
FRIENDLY DISPOSAL
According to EU directive 2002/96/EC on
electric and electronic equipment and its
implementation into national law, all electric
tools must be separately collected and
environmentally friendly recycled.
13