EINHELL TE-SD 3,6 Li Manual De Instrucciones Original página 17

6. Operation
6.1 Charging the battery (Fig. 2)
The battery is protected from exhaustive dischar-
ge. An integrated protective circuit automatically
switches off the equipment when the battery is
fl at. In this case the bit chuck will cease to turn.
Notice! Do not press the On/Off switch any more
if the protective circuit has tripped. This may da-
mage the battery.
Check that your mains voltage is the same as that
marked on the rating plate of the battery charger.
Plug the battery charger in the plug socket and
connect the charging cable to the charging con-
nection. The charging process starts as soon as
the charging cable is connected to the charging
adapter.
The red LED on the battery capacity indicator (5)
indicates that the battery is being charged. When
the charging has fi nished, the red LED will go out
and the green LED will begin to shine.
Notice! The handle may become a little warm du-
ring the charging process. This is normal.
If the battery fails to charge, please check
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts of the charging unit
If the battery still fails to charge, send
•
the charging unit
•
and the screwdriver
to our customer service center.
Timely recharging of the battery will help it serve
you well for a long time. You must recharge the
battery when you notice that the power of the
cordless screwdriver drops.
6.2 Changeover switch (Fig. 3/Item 10)
The slide switch above the On/Off switch is for
setting the direction of rotation of the cordless
screwdriver and for preventing the cordless
screwdriver from being switched on inadvertently.
You can select between clockwise and counter-
clockwise rotation. Change the direction of rota-
tion only when the equipment is at a standstill.
If you fail to observe this point, the gearing may
become damaged. When the slide switch is in the
middle position, the On/Off switch is blocked.
Anl_TE_SD_3_6_Li_Kit_SPK9.indb 17 Anl_TE_SD_3_6_Li_Kit_SPK9.indb 17
GB
6.3 On/Off switch (Fig. 3 / Item 9)
Press the On/Off switch to switch the cordless
screwdriver on. Release the On/Off switch again
to switch it off .
6.4 LED lamp (Fig. 3/Item 2)
The LED lamp (2) can be used to additionally illu-
minate the area where you want to drill or screw.
The LED lamp (2) will be lit automatically as soon
as you press the On/Off switch (9).
6.5 Angle setting (Fig. 3+4/Item 7)
The screwdriver can be locked into 2 diff erent
angle settings. To do so, press and hold the lo-
cking button (7) and move the screwdriver into the
desired position. Then release the locking button
(7) again.
Caution! Before you switch on the screwdriver,
make sure that it is correctly locked in the angle
position in question.
6.6 Battery capacity indicator (Fig. 5/Item 5)
Remove the cordless screwdriver from the char-
ging unit/charging station.
Press the button for the battery capacity indicator
(6). The battery capacity indicator (5) indicates
the charge state of the battery on 3 colored LEDs.
All the LEDs are lit:
The battery is fully charged.
The yellow and red LEDs are lit:
The battery has an adequate remaining charge.
Red LED:
The battery is empty, recharge the battery.
6.7 Torque setting (Fig. 5 / Item 3)
The torque for a particular screw size is set with
the setting ring (3). The torque is dependent on a
number of factors:
•
On the type and hardness of the material
involved
•
On the type and length of the screws used
•
On the requirements that the screw connec-
tion has to satisfy
The grating disengagement of the coupling in-
dicates that the selected torque level has been
reached.
Notice! Only ever adjust the setting ring
when the equipment is at a standstill.
- 17 -
04.10.2019 13:17:59 04.10.2019 13:17:59