Beko CWB 6610 X Manual Del Usuario página 22

Display C = Indicates the motor speed level selected and
activates the timer.
Push-button D = Switches on the cooker hood. Increases the
motor speed. Touching the key at 3rd speed, the intensive
function runs for 10' , then the appliance go back to work at
the original speed. During this function the display blinks.
Key E = The Timer times the functions on activation for
15 minutes, after which they are switched off. The Timer is
deactivated by re-pressing Key E. When the Timer is activated
the decimal point must flash on the display. The Timer cannot
be activated if the intensive speed is functioning.
The "clean air" function is activated by pressing key E for 2
seconds when the appliance is switched off.
This switches the motor on for 10 minutes every hour at the
first speed.
During functioning a rotary movement of the peripheral
segments must be visualised on the display. When this time
has passed the motor switches off and the fixed letter "C" must
be visualised on the display until the motor re-starts after 50
minutes for another 10 minutes and so on. Press any key apart
from the light keys to return to normal functioning. Press key
E to deactivate the function.
• Active carbon/grease filter saturation:
- When display item C flashes, at a speed where it alternates
with the letter F (e.g. 1 and F), the grease filters must be
washed.
- When display item C flashes, at a speed where it alternates
with the letter A (e.g. 1 and A), the active carbon filters must
be replaced or washed depending on the type of filter.
After the clean filter has been positioned correctly, the
electronic memory must be reset by pressing button A for
approximately 5 seconds, until the indication F or A shown
on the display C stops flashing.
• Mechanical controls (Fig.12): the symbols are as follows:
A= LIGHT / ON-OFF key
B= OFF /FIRST SPEED key
C= SECOND SPEED key
D = THIRD SPEED key
If the hood is shut off at first, second or third speed, when
it is turned back on, it will start at the same speed it was in
when switched off.
• Commands (Fig.13) :
A = Light Key Turn on/off lights.
B = ON/OFF Key Turn on/off the hood.
The equipment switches on at the 1st speed.
To turn off the hood press key B.
C = Display Indicates the speed of the selected motor and
activation of the timer.
D = Key Increases and decreases the speed of the motor with
a cyclical pattern, 1°-2°- 3° ... 1°-2°- 3° speed.
By pressing the key for 3 seconds the INTENSE function comes
into operation for 6 minutes, on the C display the number 4
starts flashing.
At the end of the minutes the engine will start operating at
the previously set speed.
To deactivate the intense speed, before the set time, press
the B key and the hood turns off, but not if the lights are on.
E = Timer key With any speed entered (excluding Intense
speed) by pressing the key the timer function is activated for
15 min. At the end of the count the hood turns off (motor and
any lights that are on).
To turn off the Timer function, before the pre-set time, press
the B key and the hood turns off, or by pressing the timer key
again it turns off but the hood continues to operate.
• S aturation Active carbon/Anti-grease filters:
- After 30 h of operation, with the hood ON on display C , the
letter F starts to flash which means that the anti-grease filters
have to be washed.
Once the clean filter is replaced you must reset the electronic
memory, with the hood off press key B and D for 5 sec. until
the display C shows the letter F fixed for 2 sec.
-After 120 h of operation, with the hood ON on display C the
letter C starts to flash which means that the carbon filters
have to be washed or replaced.
Once the clean filter is replaced you must do a double re-set so
with the hood off press key B and D for 5 sec. until the display
C shows the letter F fixed for 2 sec.
Repeat and press key B and D for 5 sec. until display C shows
the letter C fixed for 2 sec. .
• Commands (Fig.14)
A = ON/OFF key
Turns the hood on/off.
By pressing key A the LED flashes for 2 sec. then remains fixed
and the equipment starts in 1° speed.
To turn the hood off press key A again, the LED flashes for 2
sec. then it turns off.
B = FIRST SPEED KEY
C = SECOND SPEED Key/TIMER function
- Key C also activates the TIMER function.
- The key flashes for the full duration of the TIMER.
- With any speed entered (excluding Intense speed where
applicable) by pressing C for about 3 seconds the TIMER
function is activated for 15 min. At the end of the count the
hood turns off (motor and any lights that are on).
- To deactivate the Timer function, before the pre-set time,
press any key except the F key for ON/OFF Lights.
D = THIRD SPEED key/ INTENSE SPEED Function
- Key D also activates the INTENSE SPEED function.
- The key flashes for the full duration of the INTENSE SPEED
function.
- By pressing the key for 3 seconds the INTENSE function comes
on for 6 minutes.
- At the end of the minutes the engine will start operating at
the previously set speed.
To deactivate the intense speed, before the pre-set time, press
any key except the F key for ON/OFF Lights.
Attention! Some models only work up to the 3rd speed and,
therefore, do not have the intense function.
E = ON/OFF LIGHTS key
• S aturation Active carbon/Anti-grease filters:
- When the hood is on the LED corresponding to the A and B
keys flash, the anti-grease filters must be washed.
Once the clean filter is put back the electronic memory must
be reset, with the hood off press A for 5 sec. , the reset is
confirmed by a flashing of the LED A and B.
- When the hood is on the LED corresponding to C and E flash,
the carbon filters must be washed.
Once the clean filter is put back the electronic memory must
be reset, with the hood off press A for 5 sec. , the reset is
confirmed by a flashing of the LED C and E.
THE MANUFACTURER DECLINES ALL RESPONSIBILITY
FOR EVENTUAL DAMAGES CAUSED BY BREACHING THE
ABOVE WARNINGS.
- 20 -