Starmix St2400 Instrucciones De Montaje página 12

List of contents.
Hair- or hand-dryer
4 wall-plugs
4 half-round woodscrews
1 power lead
1 safety hexagon spanner
1 instructions for use
1 installation pattern
1 guarantee card
1 locking plug (rubber cover)
Installation sequence;
for fixed connection lead
1. Separate the cover
the back plate by.
2. lFeed the mains supply cable coming out of
the wall into the hole in the back plate left
after removing the knockout
3. Secure the back plate of the wall holder to the
wall using the plugs and screws provided.
4. Remove the terminal connector
the mains supply cable
connector , as shown in the picture, and then
secure again the terminal connector .
5. the earth cable from the wall must be con-
nected to the terminal connector. the cables
shall withstand 16A.
6. Fit the front cover of the wall holder, taking
care to locate the cable sleeve properly.
7. Secure the front cover with the screw
8. Switch on the general switch of your mains
electricity. the hairdryer is ready for use.
Installation sequence
for mobile connection lead
1. Separate the cover
the back plate by loosening the screw
2. Secure the back plate of the wall holder to the
wall using the plugs and screws provided.
3. Remove the terminal connector, connect the
mains supply cable
nector  , as shown in the picture, and then
secure again the terminal connector
4. Fit the strain relieves
5. Fit the front cover of the wall holder
6. Secure the front cover with the screw
7. Switch on the general switch of your mains
electricity. the hairdryer is ready for use.
GB- 12
 of the wall holder from


 , connect
 to the terminal



of the wall holder from

 to the terminal con-

 .


ST 2400
After operating the push-button, the appliance will
run in basic mode for about 30 sec.
Running time can be adjusted by turning the ro-
tating potentiometer inside the appliance. Only
undertake adjustments after removing the power
lead from the mains!
ST 2400 E, ST 2400 EC, ST 2400 ES
these appliances are switched on and off without
contact by an infra red proximity switch.
the sensing range is between 0 mm and 200 mm.
to prevent continuous operation, e.g. if the sensor
is shortcircuited, the appliance switches off auto-
matically after 120 sec. Once the fault is corrected,
the dryer is again ready for operation.
STH 2400 Z
After operating the push-button, the appliance will
run in basic mode for about 60 sec.
Running time can be adjusted by turning the rot
ting potentiometer inside the appliance. Only un-

dertake adjustments after removing the power
lead from the mains!
Cleaning and servicing.
Clean the air inlet openings to remove sticking fluff
and dust as required with a narrow vacuum clea-
ner fitting. Remove any dirt which is still stuck in
the air inlet with a stiff brush. the surface of the
housing may be wiped over with a damp or a dry
cloth. Abrasive cleaners must not be used.

MAINTENANCE
.
Regularly control the feeding cable looking
¾
for damages, cracks or ageing. Substitute the
cable before using it further.
If the feeding cable is damaged it must be
¾
substituted by the manufacturer or by its af-
ter sales service or in any case by a similarly
qualified person, thus preventing any possi-
.
ble risk.
When using extension electric wires ensure
¾

that they are lying on dry surfaces and pro-
tected against possible water jets.
Specialized personnel must always carry out
¾
maintenance and repairs; any damaged part
must be substituted with original spare parts.
ATTENTION: it is forbidden to carry out chan-
ges to the apparatus. Tampering could cause
fires and damages even lethal to the user and
the forfeiture of the guarantee. The manufac-
turer declines any responsibility for damages
caused to people or things due to non-compli-
ance with these instructions or if the apparatus
is unreasonably used.