Milwaukee 6955-20 Manual Del Operador página 9

Miter Miter
Range Detents (Stops)
0° to 55° Left 0°, 15°, 22.5°, 31.62°, 45° Left
0° to 60° Right 0°, 15°, 22.5°, 31.62°, 45° Right
Base Molding
Capacity
6" at 0°
6" at 45° Left and Right
Two Methods for Cutting Crown Molding
The angles created on a piece of crown
molding that fi ts fl at against the ceiling and
wall will, when added together, equal 90°
(A + B = 90°).The most common crown
molding angles are :
52 ° /38 ° : A 52° angle against the ceiling (A)
and a 38° angle against the wall (B). The
miter saw has special miter settings at 31.6°
left and right and a bevel setting at 33.9° to
use when cutting 52°/ 38° crown molding fl at
on the miter saw table. These settings are
identifi ed with a diamond mark.
45 ° /45 ° : A 45° angle against the ceiling (A)
and a 45° angle against the wall (B). The
miter saw has special miter settings at 35.3°
left and right and a bevel setting at 30° to use
when cutting 45°/ 45° crown fl at on the miter
saw table. These settings are identifi ed with
a black circle.
NOTE: Even though all of these angles are
standard, rooms are very rarely constructed
so the corners are exactly 90°. You will need
to "fi ne tune" these settings and make neces-
sary adjustments to the cutting angles.
Ceiling
Fig. 10
Angle A
Angle B
Outside
Inside
corner
corner
Bevel Bevel
Range Detents (Stops)
0° to 45° Left 0°, 22.5°, 33.85°, 45°, 48 Left
0° to 48° Right 0°, 22.5°, 33.85°, 45°, 48 Right
Nested Crown
Capacity
6-5/8"
Cutting Crown Molding Flat on the Miter
Saw Table
The advantage of cutting crown molding fl at
on the table is that it is easier to secure the
molding at the correct cutting position. Also
larger pieces of crown molding may be cut
laying fl at on the miter saw table.
1. Set the bevel and miter angles using
the Crown Molding Miter Angles chart.
Tighten the miter lock knob and the
bevel lock knob.
2. Using the Positioning section below,
correctly positions the molding.
NOTE: Always make a test cut on scrap
material to confi rm all angles are correct.
3. Make the cut according to "Making a
Chop Cut".
Cutting Crown Molding Angled Against
the Fence (Nested – in position)
Always use a crown molding fence when
cutting crown molding angled against the
fence. When cutting crown molding angled
against the fence does not require bevel set-
tings. Small changes in the miter angle can
be made without affecting the bevel angle.
When using this method the saw can be
quickly and easily adjusted for corners that
are not 90° (square).
Positioning
Standard (U.S.) crown molding with 52
and 38 ° angles (set bevel angle to 33.85°)
Left side, inside corner
1. Top edge of molding against fence
2. Miter table set right 31.62 °
3. Save left end of cut
Right side, inside corner
1. Bottom edge of molding against fence
2. Miter table set left 31.62 °
3. Save left end of cut
Left side, outside corner
1. Bottom edge of molding against fence
2. Miter table set left 31.62 °
3. Save right end of cut
Right side, outside corner
1. Top edge of molding against fence
°
2. Miter table set right 31.62
3. Save right end of cut
16
Standard (U.S.) crown molding with 45
angles (set bevel angle to 0°)
Left side, inside corner
1. Top edge of molding against fence
2. Miter table set right 45
3. Save left end of cut
Right side, inside corner
1. Bottom edge of molding against fence
2. Miter table set left 45
3. Save left end of cut
Crown Molding Miter Angles
Wall Angle 38˚ / 52˚
(B) Miter/Bevel
67 42.93/41.08
68 42.39/40.79
69 41.85/40.50
70 41.32/40.20
71 40.79/39.90
72 40.28/39.61
73 39.76/39.30
74 39.25/39.00
75 38.74/38.69
76 38.24/38.39
77 37.74/38.08
78 37.24/37.76
79 36.75/37.45
80 36.27/37.13
81 35.79/36.81
82 35.31/36.49
83 34.83/36.17
84 34.36/35.85
85 33.90/35.52
86 33.43/35.19
87 32.97/34.86
88 32.52/34.53
°
89 32.07/34.20
90 31.62/33.86
91 31.17/33.53
92 30.73/33.19
93 30.30/32.85
94 29.86/32.51
95 29.43/32.17
96 29.00/31.82
97 28.58/31.48
98 28.16/31.13
99 27.74/30.78
100 27.32/30.43
101 26.91/30.08
102 26.50/29.73
103 26.09/29.38
104 25.69/29.02
105 25.29/28.67
106 24.78/28.31
°
Left side, outside corner
1. Bottom edge of molding against fence
°
2. Miter table set left 45
3. Save right end of cut
Right side, outside corner
1. Top edge of molding against fence
° 2. Miter table set right 45
3. Save right end of cut
45˚/45˚ Wall 38˚ / 52˚
Miter/Bevel Angle (B) Miter/Bevel
46.89/36.13 107 24.49/27.95
46.35/35.89 108 24.10/27.59
45.81/35.64 109 23.71/27.23
45.28/35.40 110 23.32/26.87
44.75/35.15 111 22.93/26.51
44.22/34.89 112 22.55/26.15
43.70/34.64 113 22.17/25.78
43.18/34.38 114 21.79/25.42
42.66/34.12 115 21.42/25.05
42.15/33.86 116 21.04/24.68
41.64/33.60 117 20.67/24.31
41.13/33.33 118 20.30/23.94
40.62/33.07 119 19.93/23.57
40.12/32.80 120 19.57/23.20
39.62/32.53 121 19.20/22.83
39.13/32.25 122 18.84/22.46
38.63/31.98 123 18.48/22.09
38.14/31.70 124 18.13/21.71
37.66/31.42 125 17.77/21.34
37.17/31.14 126 17.42/20.96
36.69/30.86 127 17.06/20.59
36.21/30.57 128 16.71/20.21
35.74/30.29 129 16.37/19.83
35.26/30.00 130 16.02/19.45
34.79/29.71 131 15.67/19.07
34.33/29.42 132 15.33/18.69
33.86/29.13 133 14.99/18.31
33.40/28.83 134 14.65/17.93
32.94/28.54 135 14.30/17.55
32.48/28.24 136 13.97/17.17
32.02/27.94 137 13.63/16.79
31.58/27.64 138 13.30/16.40
31.13/27.34 139 12.96/16.02
30.68/27.03 140 12.63/15.64
30.24/26.73 141 12.30/15.25
29.80/26.42 142 11.97/14.87
29.36/26.12 143 11.64/14.48
144 11.31/14.09
28.92/25.81
28.48/25.50 145 10.99/13.71
28.05/25.19 146 10.66/13.32
17
°
°
45˚/45˚
Miter/Bevel
27.62/24.87
27.19/24.56
26.77/24.24
26.34/23.93
25.92/23.61
25.50/23.29
25.08/22.97
24.66/22.65
24.25/22.33
23.84/22.01
23.43/21.68
23.02/21.36
22.61/21.03
22.21/20.70
21.80/20.38
21.40/20.05
21.00/19.72
20.61/19.39
20.21/19.06
19.81/18.72
19.42/18.39
19.03/18.06
18.64/17.72
18.25/17.39
17.86/17.05
17.48/16.71
17.09/16.38
16.71/16.04
16.32/15.70
15.94/15.36
15.56/15.02
15.19/14.68
14.81/14.34
14.43/14.00
14.06/13.65
13.68/13.31
13.31/12.97
12.94/12.62
12.57/12.28
12.20/11.93