Before Starting The Equipment - EINHELL TE-TS 315 UD Manual De Instrucciones Original

Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
•
Unpack the bench-type circular saw and
check it for damage which may have occurred
in transit.
•
The machine has to be set up where it can
stand firmly, e.g. on a work bench, or it must
be bolted to a strong base.
•
All covers and safety devices have to be pro-
perly fitted before the machine is switched on.
•
It must be possible for the saw blade to run
freely.
•
When working with wood that has been pro-
cessed before, watch out for foreign bodies
such as nails or screws etc.
•
Before you actuate the On/Off switch, make
sure that the saw blade is correctly fitted and
that the machine's moving parts run smoothly.
6. Assembly
Danger! Pull out the power plug before carry-
ing out any maintenance, resetting or assem-
bly work on the circular saw!
6.1 Assembly of the sub-frame and table
length extension (Figs. 1, 3a-i)
Danger! Make allowance for the weight of the
machine and arrange another person to help you
if necessary!
•
Turn the bench-type circular over and set the
saw down on the floor or on some other work
surface. Important! Place suitable material
Anl_TE_TS_315_UD_SPK9.indb 32 Anl_TE_TS_315_UD_SPK9.indb 32
GB
(e.g. packaging material) between the table
surface and the surface on which it is stood to
prevent any damage to the table surface.
•
Use the hexagon screws (32), washers (35),
spring washers (36) and nuts (38) to screw
the legs (29) loosely to the saw table (1).
Important! Do not yet screw any screws into
the drill holes at the back of the table (1), as
this is where the angled plates (52) for the
table length extension (39) are to be fastened
later.
•
Use the hexagon screws (32), washers (35),
spring washers (36) and nuts (38) to screw
the cross struts (30) and longitudinal struts
(31) loosely to the legs. Make sure that the
holes in the fitted cross struts face upwards to
enable the table length extension to be fitted
later. Also make sure that the tongue-and-
groove connection between the strut and leg
engages properly.
•
Use the hexagon screws (32), washers (35),
spring washers (36) and nuts (38) to screw
the rubber feet (13) securely to the legs.
•
Fasten the extractor adapter (16) to the ma-
chine using the screws (49). Important! The
side connection socket of the extractor adap-
ter (16) must be pointing to the right.
•
Screw the angled plates (52) to the back of
the saw table (1) using the hexagon screws
(32), washers (35), spring washers (36) and
nuts (38).
•
Use the collar screws (53), washers (54)
and self-locking nuts (55) to screw the table
length extension (39) to the angled plates
(52). Important! The screw head should
point outwards and the washer (54) and self-
locking nut (55) should be on the inside.
•
Use the collar screws (53), washers (54) and
self-locking nuts (55) to screw the struts (43)
to the table length extension (39).
•
Use two hexagon screws (32), washers (35),
spring washers (36) and nuts (38) to screw
the struts (43) to the rear legs (29).
•
Turn the machine over so that it stands on
its legs. The machine must be stood on a flat
surface. Then tighten all loose screw connec-
tions.
6.2 Assembling the handles, tool hook and
chassis (Figs. 1, 4a-d)
•
Use the hexagon screws (32), washers (35),
spring washers (36) and nuts (38) to screw
the handles (42) to the front legs.
•
Screw the tool hook (34) to the front right leg.
Important! When not in use, the face spanner
- 32 -
24.03.2020 10:10:07 24.03.2020 10:10:07