Operation - EINHELL TE-MS 18/210 Li - Solo Manual De Instrucciones Original

angle between the blade (7) and the turntable
(17) equals exactly 45°.
•
The angle stop and Hexagon key (d) are not
included in the scope of this delivery – they
are available from your dealer.
5.5 Adjusting the miter angle on the machine
head (Fig. 2, 12-13)
•
Undo the locking grip (21).
•
Hold the machine head (4) by the handle (1).
•
After the locking grip is undone, the machine
head can be infinitely tilted as well as tilted to
various locking positions.
•
Angles to the left: 0-45°
•
Re-tighten the locking grip (21).

6. Operation

6.1 Charging the Li battery pack (Fig. 2, 15)
1. Remove the rechargeable battery (39) from
the mount (40) by pressing the pushlock
button on the battery and pulling it out of the
mount.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(41) into the socket outlet. The green LED will
then begin to ash.
3. Push the battery pack onto the battery char-
ger.
In section 10 (Charger indicator) you will nd a
table with an explanation of the LED indicator on
the charger.
If the battery pack fails to charge, check for the
following:
•
voltage at the power socket
•
whether there is good contact at the charging
contacts of the charging unit
If the battery pack still fails to charge, send
•
the charger and charging adapter
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
Anl_TE_MS_18_210_Li_SPK9.indb 29 Anl_TE_MS_18_210_Li_SPK9.indb 29
GB
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and res.
Warning! To make 90° crosscuts, the adjustable
stop rail (37) must be xed at the inner position:
•
Undo the locking screw (38) of the adjustable
stop rail and push the adjustable stop rail
inwards.
•
The adjustable stop rail (37) must be fixed far
enough in front of the innermost position that
the distance between the stop rail (37) and
the saw blade (7) amounts to a maximum of
5mm.
•
Before making a cut, check that the stop rail
and the saw blade cannot collide.
•
Tighten the locking screw (38) again.
Warning! To make 0°-45° miter cuts (with the saw
head inclined or the turntable set at an angle),
the adjustable stop rail must be xed at an outer
position.
•
Undo the locking screw (38) of the adjustable
stop rail and push the adjustable stop rail
outwards.
•
The adjustable stop rail (37) must be fixed far
enough in front of the innermost position that
the distance between the stop rail (37) and
the saw blade (7) amounts to a maximum of
5mm.
•
Before making a cut, check that the stop rail
and the saw blade cannot collide.
•
Tighten the locking screw (38) again.
6.2 Cross cut 90° and turntable 0°
(Fig. 1-3, 10)
•
Move the machine head (4) to its upper po-
sition.
•
Place the piece of wood to be cut at the stop
rail (11) and on the turntable (17).
•
Lock the material with the clamping device
(8) on the fixed saw table (18) to prevent the
material from moving during the cutting ope-
ration.
•
Press the release button (3) to release the
machine head (4).
•
Press the On/Off switch (2) to start the motor.
•
Use the handle (1) to move the machine head
(4) steadily and with light pressure down-
wards until the saw blade (7) has completely
cut through the workpiece.
•
When the cutting operation is completed,
- 29 -
09.03.2020 09:22:17 09.03.2020 09:22:17