Operation - EINHELL TC-SM 2131/1 Dual Manual De Instrucciones Original

•
To tilt the machine head to the right by up to
45°, proceed as follows:
- Tilt the machine head (4) by approx. 10° to
the left.
- Pull out and hold the button (33).
- Swing the machine head (4) over the 0° line
to the right.
- After reaching approx. 10° on the righthand
side, let go of the button (33).
- When the pointer (20) reaches the desired
angular setting on the scale (19), secure
the machine head (4) again with the locking
lever (21).
•
To return the machine head to 0° on the scale
(19) there is no need to press the button (33)
again.
•
To ensure that the saw is standing securely,
adjust the adjustable foot (13) by turning it so
that the saw stands in a horizontal and firm
position.
5.4 Precision adjustment of the stop rail (Fig.
6)
•
Lower the machine head (4) and fasten in
place with the retaining pin (25).
•
Fasten the turntable (17) in 0° position.
•
Place the 90° stop angle (a) between the bla-
de (7) and the stop rail (11).
•
Slacken the four adjustment screws (42)
using the 5mm hex key (40), set the stop rail
(11) to 90° in relation to the saw blade (7) and
retighten the adjustment screws (42).
•
There is no angle stop (a) included the scope
of this delivery.
5.5 Precision adjustment of the stop for cros-
scut 90° (Fig. 7a, 8)
•
Fasten the turntable (17) in 0° position.
•
Slacken the locking lever (21) and tilt the ma-
chine head (4) to 0° using the handle (1).
•
Place the 90° angular stop (a) between the
blade (7) and the turntable (17).
•
Turn the adjustment screw (26) until the ang-
le between the blade (7) and the turntable
(17) equals 90°.
•
Finally, check the position of the pointer (20)
on the scale (19).
•
If necessary, release the pointer (20) with a
crosstip screwdriver, move to the 0° position
of the scale (19) and retighten the holding
screw.
•
The angle stop (a) and crosstip screwdriver
are not included in the scope of this delivery.
•
5.6 Precision adjustment of the stop for miter
cut 45° (Fig. 7, 9)
Anl_TC_SM_2131_1_Dual_SPK8.indb 45 Anl_TC_SM_2131_1_Dual_SPK8.indb 45
GB
•
Lower the machine head (4) and fasten in
place with the retaining pin (25).
•
Fasten the turntable (17) in 0° position.
•
Undo the locking lever (21) and move the ma-
chine head (4) all the way to the left using the
handle (1), until it coincides at 45°.
•
Place the 45° stop angle (b) between the bla-
de (7) and the turntable (17).
•
Adjust the adjustment screw (29) so that the
angle between the blade (7) and the turntable
(17) equals exactly 45°.
•
To set the stop 45° on the right-hand side: Tilt
the machine head (4) to the right (see section
5.3) and set the adjustment screw (30) accor-
ding to the left-hand side.
•
No angle stop (b) included.

6. Operation

Warning! To make 90° crosscuts, the adjustable
stop rail (34) must be fi xed at the inner position:
•
Undo the locking screw (9) of the adjustable
stop rail and push the adjustable stop rail
inwards.
•
The adjustable stop rail (34) must be fixed far
enough in front of the innermost position that
the distance between the stop rail (34) and
the saw blade (7) amounts to a maximum of
8 mm.
•
Before making a cut, check that the stop rail
and the saw blade cannot collide.
•
Tighten the locking screw (9) again.
Warning! To make 0°-45° miter cuts to the left
(with the machine head (4) inclined or with the
turntable set at an angle), the adjustable stop rail
(34) must be fi xed at an outer position.
•
Undo the locking screw (9) of the adjustable
stop rail and push the adjustable stop rail
outwards.
•
The adjustable stop rail (34) must be fixed far
enough in front of the innermost position that
the distance between the stop rail (34) and
the saw blade (7) amounts to a maximum of
8 mm.
•
Before making a cut, check that the stop rail
and the saw blade cannot collide.
•
Tighten the locking screw (9) again.
Warning! This saw is equipped with a removable
stop rail (36) which is screwed to the right-hand
side of the fi xed stop rail (11). To make 0°-45°
miter cuts to the right (with the machine head
(4) inclined or with the turntable set at an angle),
- 45 -
09.07.2020 11:13:38 09.07.2020 11:13:38