Setting The Drilling Depth - Bosch GBH 36 V-LI PROFESSIONAL Instrucciones De Servicio

Ocultar thumbs Ver también para GBH 36 V-LI PROFESSIONAL:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 32
gbh36v_bu_1619929686_t.fm Seite 6 Freitag, 17. März 2006 10:14 10
Tools without SDS-plus (GBH 36 VF-LI)
Do not use tools without SDS-plus for hammer
drilling or chiselling! Tools without SDS-plus and
their drill chucks are damaged by hammer drilling or
chiselling.
Inserting the Tool (see Fig.
Place on the quick change keyless drill chuck 1 (see
Attaching the Quick Change Drill Chuck).
Hold the holding ring 25 of the quick change keyless
drill chuck fixed. Open the tool holder 3 wide enough
by turning the front sleeve 24 so that the tool can be
inserted.
Continue holding the holding ring 25 fixed and turn the
front sleeve 24 in the direction of the arrow until a
ratcheting sound can be distinctly heard.
Check the firm seating by pulling on the tool.
Note: After opening the tool holder to the stop, the
ratcheting noise can be audible at the subsequent
closing as a result of the functional design and the tool
holder does not close.
In this case, turn the front sleeve 24 once opposite to
the direction of the arrow. The tool holder can then be
closed.
Tool Removal (see Fig.
I
Hold the holding ring 25 of the quick change keyless
chuck fixed. Open the tool holder by turning the front
sleeve 24 in the direction of the arrow until the tool can
be removed.

Setting the Drilling Depth

(see Fig.
)
K
With the depth stop 17, the desired drilling depth t can
be set.
Press the button 12 of the auxiliary handle and insert
the depth stop into the auxiliary handle 18 so that the
grooved side of the depth stop points downward.
Insert the SDS-plus tool to the stop into the tool holder
3. Otherwise, the freedom of motion of the SDS tool
can lead to an incorrect setting of the drilling depth.
Pull out the depth stop so far that the distance be-
tween the drill tip and the tip of the depth stop corre-
sponds to the desired drilling depth t.
1 619 929 686 • (06.03) T
Dust Extraction with the Vacuuming
Attachment (Accessory)
Mounting the Dust Extraction Attachment
(see Fig.
)
H
For vacuuming dust, a dust extraction attachment (ac-
cessory) is required. While drilling, the dust extraction
attachment springs back so that the vacuuming head
is always held against the drilled surface.
Press the button 12 of the auxiliary handle and remove
the depth stop 17. Press the button 12 again and in-
sert the dust extraction attachment from the front into
the auxiliary handle 18.
Connect a vacuum hose (19 mm dia., accessory) to
the vacuuming opening 26 of the extraction attach-
ment.
The vacuum cleaner (e.g., GAS ...) must be suitable
for the material to be worked.
When vacuuming dry dust that is especially detrimen-
tal to health or carcinogenic, use a special vacuum
cleaner.
Setting the Drilling Depth on the Dust Extrac-
)
tion Attachment (see Fig.
The desired drilling depth t can also be set with the
dust extraction attachment mounted.
Insert the SDS-plus tool to the stop into the tool holder
3. Otherwise, the freedom of motion of the SDS tool
can lead to an incorrect setting of the drilling depth.
Loosen the winged screw 30 on the dust extraction at-
tachment.
Place the machine (without switching on) firmly on the
surface to be drilled. The SDS-plus tool must rest
against the surface.
Slide the guide tube 31 of the dust extraction attach-
ment in its holder so that the dust extraction attach-
ment head rests against the surface to be drilled. Do
not slide the guide tube 31 any further over the tele-
scope tube 29 than necessary so that as large a part
as possible of the scale on the telescope tube 29 re-
mains visible.
Retighten the winged screw 30. Loosen the clamping
screw 27 on the depth stop of the dust extraction at-
tachment.
Slide the depth stop 28 on the telescope tube 29 such
that the distance t shown in the Figure
sponds to the desired drilling depth (distance between
the outer end of the guide tube 31 and the inner side
of the depth stop 28).
Retighten the clamping screw 27 in this position.
English–6
)
L
)
M
corre-
M

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Gbh 36 vf-li professional

Tabla de contenido