Serial Numbers - Peg-Perego Pliko P3 Instrucciones De Uso

- press down with both hands on the sides of the
Navetta, until it clicks into place;
- to remove the Navetta from the chassis and for more
information, please refer to the instruction manual.
PLIKO P3 + Primo Viaggio: to fasten the car seat to the
stroller proceed as follows (fig_b):
- set the brakes on the stroller;
- lower the stroller backrest completely;
- raise the stroller Ganciomatic hooks;
- place the car seat so that it faces the mother and press
it down until it clicks into place;
- It is important not to remove the front bar from the
stroller when fastening the car seat (for fastening the
front bar, please see point 23);
- To remove the car seat from the stroller, please refer to
its instructions manual.
1 0• HOOD: To fit the hood, push the side fasteners
downwards until they click into place (Fig.a); button the
hood to the inside of the armrest (Fig.b),
1 1• and to the backrest on the stroller (Fig.c).
To remove the hood (Fig.d) disengage the side
fasteners and unbutton it from the inside of the armrest
and from the backrest on the stroller.
1 2• You can detach the back part of the fabric by unzipping it
and use the hood also as a sun canopy (Fig.a). To reattach
the back part of the fabric, close the zipper (Fig.b).
1 3• By lowering the stroller backrest, the rear hood extends and
through the double zipper a window can be created to allow
more air to circulate and watch the child when sleeping.
1 4• COVER: to fasten the cover to the stroller, zip it onto the
footrest (Fig.a), button it on both sides (Fig.b) and fit it
including the front bar (Fig.c).
1 5• Depending on the models, 3 different ways to fasten
the cover correctly are available.
1 6• REVERSIBLE SEAT: it is found only in the Soft model.
First remove the straps from the backrest (paragraph 20
a-b) and remove the leg divider from underneath the
seat (paragraph 30A2). Undo both buttons on the seat
and through the zipper remove the sack repositioning
it on the desired side. Reattach the straps.
1 7• RAIN CANOPY: to fit the rain canopy, extend it over the
stroller and snap fit the buttons on both sides of the
hood (Fig.a).
Fasten the elastic loops including the chassis in the
lower part of the stroller (Fig.b).
• Do not use the rain canopy indoors and always make
sure that the child is not too hot.
• Do not place the rain canopy near heat sources and pay
attention to cigarettes.
• Make sure that the rain canopy does not interfere with
any moving mechanism of the stroller.
• Always remove the rain canopy before folding up the stroller.
• Wash with a sponge and soapy water. Do not use detergents.
1 8• 5-POINT SAFETY HARNESS: to fasten, insert the two
buckles of the waist strap (with attached shoulder
straps, arrow a) into the leg divider strap until they
click into place (arrow b). To unfasten, push the round
button placed in center of the buckle upwards (arrow_
c) and pull the waist strap outwards (arrow d).
1 9• To tighten the waist strap, pull on both sides in the direction
of the arrow (Fig.a). To loosen it do the opposite. The waist
strap can be tightened as far as the safety lock (Fig_b).
PlikoP3_FI001001I72.indd 19
2 0• To adjust the height of the safety harnesses, release the
two buckles on the rear of the backrest.
Pull the shoulder straps towards you (arrow a) until the
buckles are released and insert them in the backrest
loops (arrow b). Remove the shoulder straps from the
sack (arrow c) and insert them in the most appropriate
buckle (arrow d), then reattach the two buckles
behind the backrest (arrow e). The buckles are securely
attached when a click is heard (fig f).
2 1• ADJUSTING THE FOOTREST: the footrest can be adjusted
to three positions. To lower the footrest, pull the two
side levers downwards while lowering the footrest. To lift
the footrest, pull it upwards until it clicks into place.
2 2• ADJUSTING THE BACKREST: the backrest reclines to four
different positions. To lower the backrest, lift the handle
while lowering the backrest, locking it in the desired
position. To raise it, pull the backrest upwards.
2 3• FRONT BAR: the chassis is fitted with caps closing
the ends of the armrests; to fasten the front bar, first
remove the caps. Keep the caps in case you may want
to use the stroller without the front bar. To remove the
caps, press the button under the armrest while pulling
the cap off. Proceed on both armrests (Fig.a). To fasten
the front bar, slip both ends of the front bar into the
armrests until it clicks into place (Fig.b).
2 4• The front bar can be opened to one side only to allow
the child to get in and out of the stroller easier when he
or she is older. To open the front bar, press the button
under the armrest while pulling out the front bar (Fig.a).
To remove the front bar, press the two buttons under
the armrests while pulling out the front bar (Fig.b).
2 5• REAR LEDGE: the rear ledge helps the mother overcome
small bumps and can also be used to carry a second
child (fig_a).
LOADING SEQUENCE: to use the Pliko P3 with two
children (fig_b), first set the brakes on the stroller,
then place the smaller child in the seat and fasten the
safety harness (1). Hold the handlebars (2) and have the
second child stand on the ledge (3).
• Never leave your children unattended.
• Do not allow a child to stand on the rear ledge when
the stroller is empty.
2 6• FOLDING UP: before folding up Pliko P3, remove the
Navetta or the PrimoViaggio car seat. The stroller can
be folded up using one hand only: pull first one lever
upwards and then the other, until they click.
2 7• Hold the central handlebar and pull it upwards until the
stroller folds up (fig_a). Check the correct closure of the
chassis from the safety hook. When folded, the chassis
will stand upright (fig_b).
2 8• CARRYING: Pliko P3 can be conveniently carried by the
central handle (with the front wheels set on stationary)
(fig.a). It can also be carried by the side handle (fig_b).
2 9• REMOVABLE LINING: to remove the lining from the
stroller, unhook the sack fasteners from the armrests,
as shown by the arrows (fig_a). Unscrew the strap (one
side only) keeping your finger under the nut (fig_b).
3 0• Undo the side button on the sack and slip the leg
divider of the strap out from under the seat (fig_a).
Unbutton the sack from the seat, slip it off the hooks on
the footrest and then remove it from the top (fig_b).

SERIAL NUMBERS

3 1• Behind the Pliko P3 backrest information relating to
product name, date of manufacture and serial number
- 19 -
15-02-2010 9:45:47