HIKOKI C 10FCH2 Instrucciones De Manejo página 18

English
SPECIFICATIONS
Max. Cutting
Capacity
Height × Width
Saw Blade Dimensions (oD × iD × Thickness)
Maximum kerf
Miter Cutting Angle
Bevel Cutting Angle
Compound Cutting Angle
Voltage (by areas)*
Power Input*
No-Load Speed
Machine Dimensions (Width × Depth × Height)
Weight (Net)**
Laser Marker
(Only Model C10FCH2)
* Be sure to check the nameplate on product as it is subject to change by areas.
** According to EPTA-Procedure 01/2014
STANDARD ACCESSORIES
(1) 255 mm TCT Saw blade (mounted on tool) .................1
(2) Dust bag .......................................................................1
(3) 10 mm Box wrench .......................................................1
(4) Vise Assembly ..............................................................1
(5) 4 mm Hex. bar wrench (only C10FCH2).......................1
(6) Sub Fence (B) ..............................................................1
(7) Flat screw .....................................................................1
(8) M6 Nylon nut ................................................................1
(9) Plate (A) ........................................................................1
(10) Holder (B) .....................................................................1
(11) Side handle ..................................................................1
Standard accessories are subject to change without notice.
OPTIONAL ACCESSORIES (SOLD
SEPARATELY)
(1) Extension Holder and Stopper
(2) Crown molding Vise Ass'y (Include Crown molding
Stopper (L))
(3) Crown molding Stopper (L)
(4) Crown molding Stopper (R)
Optional accessories are subject to change without notice.
APPLICATION
○ Cutting various types of aluminium sash and wood.
UNPACKING
○ Carefully unpack the power tool and all related items
(standard accessories).
○ Check carefully to make certain all related items
(standard accessories) are present.
18
0°
Miter 45°
Bevel Left 45°
Compound (Bevel Left 45°, Miter 45°)
Maximum output
(Iambda)
Laser medium
255 mm × 30 mm × 2.3 mm
Right and Left 0° – 52°
Miter (Right and Left) 0° – 45°
460 mm × 628 mm × 561 mm
11.6 kg (C10FCH2) / 11.5 kg (C10FCE2)
Po<3 mW Class
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specifi ed on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position. If
the plug is connected to a receptacle while the trigger
switch is in the ON position, the power tool will start
operating immediately, inviting serious accident.
3. Extension cord
When the work area is removed from the power source,
use an extension cord of suffi cient thickness and rated
capacity. The extension cord should be kept as short as
practicable.
4. When the power tool is prepared for shipping, its
main parts are secured by a locking pin
Move the handle slightly so that the locking pin can be
disengaged.
CAUTION
○ Set for transport
Lock the locking pin into the gear case (Fig. 3).
Lower guard cover the teeth of the blade to the front of
the machine.
○ Cutting work
Move the handle slightly so that the locking pin can be
disengaged.
5. Attach the dust bag to the main unit (Fig. 1)
(1) When the dust bag has become full of sawdust, dust
will be blown out of the dust bag when the saw blade
rotates.
Check the dust bag periodically and empty it before it
becomes full.
(2) During bevel and compound cutting, attach the dust
bag at a right angle to the base surface as shown in
Fig. 4.
59 mm × 144 mm
or
89 mm × 101 mm
59 mm × 102 mm
41 mm × 144 mm
41 mm × 102 mm
2.7 mm
Left 0° – 45°
(110 V, 230 V)
1520 W
5000 min
–1
Laser Product
654 nm
Laser Diode