Maintenance And Inspection - HIKOKI C 10FCH2 Instrucciones De Manejo

English
(7) Press in the spindle lock and tighten the bolt by turning
it to the left by standard accessories wrench(10 mm box
wrench) as indicated in Fig. 27.
CAUTION
○ Confi rm that the spindle lock has returned to the retract
position after installing or removing the saw blade.
○ Tighten the bolt so it does not come loose during
operation.
○ Confi rm that the bolt has been properly tightened
before the power tool is started.
2. Dismounting the saw blade
Dismount the saw blade by reversing the mounting
procedures described in paragraph 1 above.
The saw blade can easily be removed after lifting the
lower guard.
CAUTION
○ Never attempt to
245 mm – 255 mm in diameter.
TRANSPORTATION OF THE MAIN BODY
(Fig. 29)
The vice assembly could be dropped during transportation.
Either remove the assembly or slip a piece of wood between
the vice to fi rmly secure it.
Drop the head and insert the locking pin (Fig. 3).
Turn and loosen the side handle, turn the turntable as far
right as it will go, and secure the turntable by turning the
handle to the fi xed position. This will make the main body
even more compact.
When transporting the main body, carry it in your arms,
holding the grip located on the base with both hands or
carry handle.

MAINTENANCE AND INSPECTION

WARNING
To avoid an accident or personal injury, always confi rm
the trigger switch is turned OFF and that the power plug
has been disconnected from the receptacle before
performing any maintenance or inspection of this tool.
1. Inspecting the saw blade
Always replace the saw blade immediately upon the
fi rst sign of deterioration or damage.
A damaged saw blade can cause personal injury and
a worn saw blade can cause ineff ective operation and
possible overload to the motor.
CAUTION
○ Never use a dull saw blade. When a saw blade is dull,
its resistance to the hand pressure applied by the tool
handle tends to increase, making it unsafe to operate
the power tool.
2. Inspecting the lever (Fig. 30 and Fig. 31)
If the M6 hexagonal head bolts (2) are loose, align the
sides of the fence and saw blade with the steel square.
After adjusting the saw blade and fence to a ninety-
degree angle, tighten the lever securing hexagonal
head bolts (2).
3. Inspecting the carbon brushes (Fig. 32 and Fig. 33)
The carbon brushes in the motor are expendable parts.
If the carbon brushes become excessively worn, motor
trouble might occur.
Therefore, inspect the carbon brushes periodically and
replace them when they have become worn to the wear
limit line as shown in Fig. 32.
Also, keep the carbon brushes clean so that they will
slide smoothly within the brush holders.
22
install saw blades except
The carbon brushes can easily be removed after
removal of the brush caps (see Fig. 33) with a slotted
(minus) screwdriver.
4. About Handling the Motor (see Fig. 1)
Winding of the motor is said to be the heart of this tool.
Exercise utmost caution not to damage the winding by
exposing it to wash oil or water.
NOTE
○ Accumulation of dust and the like inside the motor can
result in a malfunction.
After using the motor for 50 hours or so, carry out no-
load running, and blow in the dry air from a wind hole at
the motor's rear. Such action is eff ective to discharge
dust and the like.
5. Inspecting the screws
Regularly inspect each component of the power tool for
looseness.
Re-tighten screws on any loose part.
WARNING
○ To prevent personal injury, never operate the power tool
if any components are loose.
6. Replacing supply cord
If the supply cord of Tool is damaged, the Tool must be
returned to HiKOKI Authorized Service Center for the
cord to be replaced.
7. Inspecting the lower guard for proper operation
Before each use of the tool, test the lower guard (see
Fig. 7) to assure that it is in good condition and that it
moves smoothly.
Never use the tool unless the lower guard operates
properly and it is in good mechanical condition.
8. Storage
After operation of the tool has been completed, check
that the following has been performed:
(1) Trigger switch is in OFF position,
(2) Power plug has been removed from the receptacle,
(3) When the tool is not in use, keep it stored in a dry place
out of the reach of children.
9. Lubrication
Lubricate the following sliding surfaces once a month
to keep the power tool in good operating condition for a
long time (Fig. 1 and Fig. 2).
Use of machine oil is recommended.
Oil supply points:
* Rotary portion of hinge
* Rotary portion of vise assembly
10. Cleaning
Periodically remove chips, dust and other waste
material from the surface of the power tool, especially
from the inside of the lower guard with a damp, soapy
cloth. To avoid a malfunction of the motor, protect it from
contact with oil or water.
Clean the machine, duct, lower guard, by blowing with
dry air from an air gun or other tool. (Fig. 34)
(Only Model C10FCH2)
If the laser line becomes invisible due to chips and the
like adhered onto the window of the laser marker's light-
emitting section, wipe and clean the window with a dry
cloth or a soft cloth moistened with soapy water, etc.
CAUTION
○ In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each
country must be observed.