Practical Applications - HIKOKI C 10FCH2 Instrucciones De Manejo

CAUTION
○ Empty the dust bag frequently to prevent the duct and
the safety cover from becoming clogged.
Sawdust will accumulate more quickly than normal
during bevel cutting.
6. Installation
Ensure that the machine is always fi xed to bench.
Attach the power tool to a level, horizontal work bench.
Select 8 mm diameter bolts suitable in length for the
thickness of the work bench.
Bolt length should be at least 35 mm plus the thickness
of the work bench.
For example, use 8 mm × 60 mm bolts for a 25 mm thick
work bench.
ADJUSTING THE POWER TOOL PRIOR TO USE
CAUTION
Make all necessary adjustments before inserting the
plug in the power source.
1. Check to see that the lower guard operates
smoothly
CAUTION
○ This compound miter saw is equipped with a saw head
lock as safety device.
○ To lower the saw head to cut, the lock must be released
by pressing the lock lever (C) with your thumb.
(1) When you push down the handle while pushing the lock
lever (C), check that the lower guard revolves smoothly
(Fig. 5).
(2) Next, check that the lower guard returns to the original
position when the handle is raised.

PRACTICAL APPLICATIONS

WARNING
○ To avoid personal injury, never remove or place a
workpiece on the table while the tool is being operated.
○ Never place your limbs inside of the line next to warning
sign while the tool is being operated. This may cause
hazardous conditions (see Fig. 6).
CAUTION
○ It is dangerous to remove or install the workpiece while
the saw blade is turning.
○ When sawing, clean off the shavings from the turntable.
○ If the shavings accumulate too much, the saw blade
from the cutting material will be exposed. Never subject
your hand or anything else to go near the exposed
blade.
1. Tightly secure the material by vise assembly to be
cut so that it does not move during cutting
2. Switch operation (Fig. 7)
The tool will not start unless the Lock-off button is
pressed while the switch is pulled back.
The Lock-off button can be engaged by pressing it from
the left.
After the switch is on, the saw blade will continue to
operate as long as you pull on the switch trigger, even if
you release the Lock-off button.
When the switch is released, the Lock-off button
automatically disengages to prevent inadvertent motor
startup.
WARNING
Never lock the Lock-off button in depressed position.
Pulling back the switch would then cause the tool to
suddenly start operating, which could result in injury.
3. Holder (B), clamp lever adjustment (Fig. 8)
Attach the included holder (B) in the position as shown
in Fig. 8 and adjust the holder (B) until its bottom surface
contacts the work bench surface. After adjustments,
securely tighten the 6mm bolt with the included 10mm
box wrench. Loosen the M6 × 20 screw on the clamp
lever and attach to a position where the clamp lever can
be easily operated.
4. Using the Vise Assembly (Standard accessory)
(Fig. 9)
(1) The vise assembly can be mounted on either the left
fence {Fence (B)} or the right fence {Fence (A)} by
loosening the 6 mm wing bolt (A).
(2) The screw holder can be raised or lowered according to
the height of the workpiece by loosening the 6 mm wing
bolt (B). After the adjustment, fi rmly tighten the 6 mm
wing bolt (B) and fi x the screw holder.
(3) Turn the upper knob and securely fi x the workpiece in
position.
WARNING
○ Always fi rmly clamp or vise to secure the workpiece to
the fence; otherwise the workpiece might be thrust from
the table and cause bodily harm.
CAUTION
○ Always confi rm that the motor head does not contact
the vise assembly when it is lowered for cutting. If there
is any danger that it may do so, loosen the 6 mm wing
bolt and move the vise assembly to a position where it
will not contact the saw blade.
5. Install the sub fence (B) (Fig. 10)
In the case of direct angle cutting and angle cutting, use
the sub fence. The sub fence (B) can be installed on
the right side of the guide fence (B). Place the attached
plate (A) in the position as shown in Fig. 10, insert the
tip in the groove of fence (B) and simultaneously, insert
fl athead screw M6 into fence (B), sub fence (B), and
plate (A), then tighten nylon nut M6 with the included
10mm box wrench until the sub fence (B) can smoothly
rotate. Then, you can realize stable cutting of the
material with a wide back face.
WARNING
In the case of left bevel cutting, rotate the sub fence (B).
Supposing it is not able to rotate it, it will contact the
blade or some part of the tool, causing in serious injury
to operator.
6. Using an ink line
Upon lowering the motor section, the lower guard is
raised and the saw blade appears.
Align the ink line with the saw blade.
CAUTION
Never lift the lower guard while the saw blade is rotating.
The sub fence will not only make contact and adversely
aff ect cutting accuracy, this could also result in damage
to the guard.
7. Install the side handle (Fig. 11)
Remove the M10 bolt and install the side handle that
came enclosed with this unit.
8. Position adjustment of laser line (Only Model
C10FCH2)
Ink lining can be easily made on this tool to the laser
marker. A switch lights up the laser marker (Fig. 12).
Depending upon your cutting choice, the laser line can
be aligned with the left side of the cutting width (saw
blade) or the ink line on the right side.
The laser line is adjusted to the width of the saw blade
at the time of factory shipment. Adjust the positions of
the saw blade and the laser line taking the following
steps to suit the use of your choice.
English
19