Solo 620 Instrucciones De Manejo página 13

C) Instructions on using the chain saw safely
16. Attention! Read the Operating Instructions care-
fully and have yourself instructed in the use of a
chain saw before you use it for the first time.
17. Always store your electric tools in a safe place.
Electric tools not being used should be stored in a
dry, inaccessible or locked place, outside the
reach of children.
18. Use the cable only for the intended purpose. Never
carry or suspend electric devices by the cable. Do
not use the cable to pull the plug from the socket.
Protect the cable from heat, oil and sharp edges.
19. Check the extension cable regularly and replace it
if it gets worn or damaged. Keep the handle dry
and free of oil and grease.
20. Pull the plug from the socket when replacing the saw
chain or sword.
21. Do not leave the tool key in the ignition. Check
before switching on that the key and adjustment
tools are removed.
22. Avoid accidental starting. Do not hold your finger on
the switch when carrying an electric tool that is
connected to the power source. Ensure that the
switch is off when the plug is inserted in the socket.
23. Damaged switches have to be replaced by a
customer service workshop. Do not use an electric
tool if the switch cannot be switched on or off.
24. Caution: Only use accessories or parts that are listed
in the operating instructions. Use of other tools and
other accessories mean safety risks for the
operator.
25. Never subjekt the electrical chain saw to rain and do
not work in wet surroundings.
26. Check the chain saw for its proper operating state
before every use.Please pay special attention to the
sword and chain.
27. Check the power cable for damage or cracks every
time before you use it. Damaged cables must be
replaced.
28. Always hold the chain saw with both hands while
working with it.
29. No other person may be within the working range of
the chain saw.
30. The chain saw must be disconnected from the power
supply before you tighten the chain, exchange the
chain or carry out any other work on the saw. -
Withdraw the plug!
31. During work breaks put the machine down in such a
manner that nobody is at risk.
32. Always use the chain cover when transporting the
chain saw.
33. When switching on the chain saw, ensure that it is
supported well and hold it firmly. The chain and bar
must be free.
34. Before you start working ensure that you are stan-
ding firmly.
35. Withdraw the plug immediately if the power cable is
damaged or cut.
36. Never cut with the tip of the bar - the saw may recoil
("kick-back").
37. Do not use the chain saw near combustible gases
or dust - danger of explosion.
38. The chain saw may only be connected to socket
outlets with earthing contact and tested electrical
installations. We recommend the use of a residual-
current-operated circuit-breaker. The fuse must have
a value of 16 A and mustn't be used by other
consumers while working with the chain saw.
39. The cable must be winded off completely when you
use a cable drum.
40. Ensure that the power cable has no kinks and is
not damaged.
41. The chain saw may only be used in a completely
assembled state. No protective devices may be
missing.
42. Switch the chain saw off immediately if you notice
any changes in the machine.
43. Always have a first-aid kit fulfilling DIN 13164 at
hand in case of accidents.
44. If the chain saw comes into contact with earth,
stones, nails or other foreign objects, withdraw the
plug immediately and check the chain as well as
the bar.
45. Ensure that no chain oil penetrates into the earth or
sewage. Always place the chain saw on something
that will absorb any oil dripping from the bar or chain.
D) Warning to the danger of recoil ("kickback")
46. Attention: If the tip of the bar contacts a hard
object while the motor is running, the saw may
recoil dangerously. In recoiling, the chain saw is
flung upwards at high speed towards the person
holding the chain saw.
47. Do not touch wood or branches with the bar tip.
48. If possible, use a stand.
49. Always keep an eye on the bar tip.
50. Only place a running saw on the object to be cut.
Never start the machine while the chain rests on
something.
51. So called piercing cuts with the bar tip may only be
carried out by trained personnel.
E) Instructions on safe working techniques
52. Before starting to work ensure that there is sufficient light.
53. Always maintain a normal body posture when operat-
ing the device. Always keep your balance.
54. Do not work with your body bent forwards.
55. Ensure that you are standing securely and do not
work on snow, ice or newly-barked wood. Danger of
slipping!
56. Working on ladders, scaffoldings or trees is forbidden.
57. Do not use chain saw above shoulder height.
58. Use the chain saw only to cut wood. It is absolutely
forebidden to cut plastics or minerals (gas concrete).
59. Ensure that the wood cannot twist while it is being cut.
60. Never climb on a tree to cut wood.
61. Watch out for splintering wood. While you are
sawing you may be injured by flying wood chips.
62. Do not use the chain saw to lever or move the wood.
63. Only cut with the lower section of the saw. The saw
will be repulsed towards you if you try and cut with
the upper section of the saw.
64. Ensure that the wood is free of stones, nails or other
foreign objects.
GB-2