Cub Cadet LTX1046 Manual Del Usuario página 26

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

4.
To properly sharpen the cutting blades, remove equal
amounts of metal from both ends of the blades along the
cutting edges, parallel to the trailing edge, at a 25°- to 30°
angle. Always grind each cutting blade edge equally to
maintain proper blade balance. See Figure 7-7.
CAUTION:
previously been sharpened, or if any metal
separation is present, replace the blades with new
ones.
WARNING!
excessive vibration, may cause damage to the
tractor and/or result in personal injury.
5.
Test the blade's balance using a blade balancer. Grind
metal from the heavy side until it balances evenly.
NOTE: When replacing the blade, be sure to install the
blade with the side of the blade marked ''Bottom'' (or with
a part number stamped in it) facing the ground when the
mower is in the operating position.
CAUTION:
blade spindle hex flange nut to between 70 ft-lbs
and 90 ft-lbs.
Battery
CALIFORNIA PROPOSITION 65 WARNING
Battery posts, terminals, and related accessories
contain lead and lead compounds, chemicals known
to the State of California to cause cancer and
reproductive harm. Wash hands after handling.
CAUTION:
NEGATIVE (Black) wire from it's terminal first,
followed by the POSITIVE (Red) wire. When re-
installing the battery, always connect the POSITIVE
(Red) wire its terminal first, followed by the
NEGATIVE (Black) wire.
26
S
7— S
ection
ervice
Figure 7-7
If the cutting edge of the blade has
A poorly balanced blade will cause
Use a torque wrench to tighten the
If removing the battery, disconnect the
Jump Starting
WARNING!
battery. Be certain the vehicles do not touch and
ignitions are off. Do not allow cable clamps to touch.
1.
Connect positive (+) cable to positive post (+) of your
tractor's discharged battery.
2.
Connect the other end of the cable to the positive (+) post
of the jumper battery.
3.
Connect the second cable negative (–) to the other post of
the jumper battery.
4.
Make the final connection on the engine block of the
tractor, away from the battery. Attach to an unpainted part
to assure a good connection.
CAUTION:
vehicle (i.e. car, truck), do NOT start the vehicle's
engine when jump starting your tractor.
5.
Start the tractor (as instructed in the Operation section of
this manual).
6.
Set the tractor's parking brake before removing the jumper
cables, in reverse order of connection.
Charging
WARNING!
while charging. Charge the battery in a well
ventilated area and keep away from an open flame
or pilot light as on a water heater, space heater,
furnace, clothes dryer or other gas appliances.
CAUTION:
use only a charger designed for 12V lead-acid
batteries. Read your battery charger's Owner's
Manual prior to charging your tractor's battery.
Always follow its instructions and heed its warnings.
If your tractor has not been put into use for an extended period
of time, charge the battery as follows:
1.
Set your battery charger to deliver a max of 10 amperes.
2.
If your battery charger is automatic, charge the battery
until the charger indicates that charging is complete. If the
charger is not automatic, charge for no fewer than eight
hours.
Fuse
WARNING!
:
inspecting, always disengage PTO, set parking
brake, stop engine and remove key to prevent
unintended starting.
A 20 Amp fuse is installed in your tractor's wiring harness to
protect the tractor's electrical system from damage caused by
excessive amperage.
If the electrical system does not function, or your tractor's engine
will not crank, first check to be certain that the fuse has not
blown. It is located under the hood, mounted behind the top of
the dash panel on the support bar.
Never jump start a damaged or frozen
If the jumper battery is installed on a
Batteries give off an explosive gas
When charging your tractor's battery,
Before servicing, repairing, or

Publicidad

Tabla de contenido

Solución de problemas

loading

Este manual también es adecuado para:

Ltx1050Ltx1046kwLtx1050kw

Tabla de contenido