Sony PlayStation 2 Manual De Instrucciones página 2

Ocultar thumbs Ver también para PlayStation 2:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

2
WARNING
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.
To avoid electrical shock, do not disassemble.
Refer servicing to qualified personnel only.
Caution
The use of optical instruments with this
product will increase eye hazard. As the
laser beam used in this unit is harmful to
eyes, do not attempt to disassemble the
cabinet.
Refer servicing to qualified personnel only.
This label is located on the Laser protective housing inside
the enclosure of the PlayStation
2 console.
®
This graphical symbol with supplemental marking is
located on the right surface of the PlayStation
®
(when it is in a vertical position).
This symbol is intended to alert the user to the
presence of uninsulated "dangerous voltage"
within the product's enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock to persons.
This symbol is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the console.
Caution
TO PREVENT ELECTRIC SHOCK, MATCH
WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
To reduce the risk of fire, use only No. 26
AWG or larger telecommunication line
cord.
For questions about AWG numbers, contact our technical
support line at 1-800-345-7669.
Information
PlayStation
2 console and network adaptor
®
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV
technician for help.
If you have questions about this product, call our
technical support line at 1-800-345-7669, or write to:
Sony Computer Entertainment America
Consumer Services/Technical Support
PO Box 5888, San Mateo, CA 94402-0888 U.S.A.
Declaration of Conformity
Trade Name :
SONY
Model No. :
SCPH-50001/N
SCPH-50010/N
Responsible Party :
Sony Electronics Inc.
Address :
680 Kinderkamack Road
2 console
Oradell, NJ 07649 U.S.A.
Telephone No. :
201-930-6972
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
You are cautioned that any changes or modifications not
expressly approved in this manual could void your
authority to operate this equipment.
Network adaptor
For customers in the USA
This network adaptor complies with Part 68 of the FCC
rules and the requirements adopted by the ACTA. On the
bottom surface of this network adaptor is a label that
contains, among other information, a product identifier in
the format US:AAAEQ##TXXXX. If requested, this
number must be provided to the telephone company.
The Ringer Equivalence Number (REN) is used to
determine the number of devices that may be connected to
a telephone line. Excessive RENs on a telephone line may
result in the devices not ringing in response to an
incoming call. In most but not all areas, the sum of the
RENs should not exceed five (5.0). To be certain of the
number of devices that may be connected to a line, as
determined by the total RENs, contact the local telephone
company. For products approved after July 23, 2001, the
REN for this product is part of the product identifier that
has the format US:AAAEQ##TXXXX. The digits
represented by ## are the REN without a decimal point
(e.g., 03 is a REN of 0.3). For earlier products, the REN is
separately shown on the label.
A jack used to connect this equipment to the premises
wiring and telephone network must comply with the
applicable FCC Part 68 rules and requirements adopted by
the ACTA.
This product uses the "RJ-11C" telephone jack.
If this equipment causes harm to the telephone network,
the telephone company will, when practical, notify you in
advance that temporary discontinuance of service may be
required. If advance notice is not practical, the telephone
company will notify you as soon as possible. Also, you
will be advised of your right to file a complaint with the
FCC if you believe it is warranted.
The telephone company may make changes to its facilities,
equipment, operations or procedures that could affect the
operation of equipment. If this happens, the telephone
company will provide advance notice so you can make the
necessary modifications to maintain uninterrupted service.
If you have questions about this product, call our technical
support line at 1-800-345-7669, or write to:
Sony Computer Entertainment America
Consumer Services/Technical Support
PO Box 5888, San Mateo, CA 94402-0888 U.S.A.
This equipment cannot be used on telephone company
provided coin service. Connection to party line service is
subject to state tariffs.
Repair of this product should be made only by an
authorized Sony Service Center. For the Sony Service
Center nearest you, call 1-800-345-7669.
Telephone Consumer Protection Act of 1991
The Telephone Consumer Protection Act of 1991 makes it
unlawful for any person to use a computer or other
electronic device to send any message via a telephone
facsimile machine unless such message clearly contains, in
a margin at the top or bottom of each transmitted page or
on the first page of the transmission, the date and time it is
sent and an identification of the business, other entity, or
individual sending the message, and the telephone
number of the sending machine or such business, other
entity, or individual. In order to program this information
into your facsimile machine, see your facsimile software
documentation.
For customers in Canada
This product is Industry Canada label identified
equipment. This certification means that the equipment
meets certain telecommunications network protective,
operational and safety requirements as prescribed in the
appropriate Terminal Equipment Technical Requirements
document(s). The Department does not guarantee the
equipment will operate to the user's satisfaction. Before
installing this equipment, users should ensure that it is
permissible to be connected to the facilities of the local
telecommunications company. The equipment must also
be installed using an acceptable method of connection.
The customer should be aware that compliance with the
above conditions may not prevent degradation of service
in some situations.
Repairs to certified equipment should be coordinated by a
representative designated by the supplier. Any repairs or
alterations made by the user to this equipment, or equipment
malfunctions, may give the telecommunications company
cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the
electrical ground connections of the power utility,
telephone lines and internal metallic water pipe system, if
present, are connected together. This precaution may be
particularly important in rural areas.
Caution: Users should not attempt to make such
connections themselves, but should contact the appropri-
ate electric inspection authority or an electrician.
NOTICE: The Ringer Equivalence Number (REN)
assigned to each terminal device provides an indication of
the maximum number of terminals allowed to be
connected to a telephone interface.
The terminals on an interface may consist of any
combination of devices subject only to the requirement
that the sum of the Ringer Equivalence Number of all the
devices does not exceed five (5.0).
The Ringer Equivalence Number for this equipment is 0.1.
The term "IC:" before the certification/registration
number only signifies that the Industry Canada technical
specifications were met.
Before operating your PlayStation
2 console
®
A very small percentage of individuals may experience
epileptic seizures when exposed to certain light patterns or
flashing lights. Exposure to certain patterns or
backgrounds on a television screen or while playing video
games, including games played on the PlayStation
2
®
console, may induce an epileptic seizure in these
individuals. Certain conditions may induce previously
undetected epileptic symptoms even in persons who have
no history of prior seizures or epilepsy.
If you, or anyone in your family, has an epileptic condition,
consult your physician prior to playing. If you experience
any of the following symptoms while playing a video
game - dizziness, altered vision, eye or muscle twitches,
loss of awareness, disorientation, any involuntary
movement, or convulsions - IMMEDIATELY discontinue
use and consult your physician before resuming play.

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Scph-50001/nScph-50010/n9701497016

Tabla de contenido