Installing The Plates; Fuel And Engine Oil; Controls; On- / Off Switch - Stihl GH 460 Manual De Instrucciones

Installing the ejection chute extension
● Attach the ejection chute extension (L),
engage the hooks (1) in the apertures
on the housing (2) from above, turn
downwards and push on the
retainers (3) at the side.
● Screw in the screws (O) and tighten to
1 - 2 Nm.
In order to facilitate installation of
the guiding plate, we recommend
loosening the left wheel carrier
slightly.
● Loosen the screw (4) at the left wheel
carrier by approx. 5 turns.

7.7 Installing the plates

1 Install the guiding plate
● Insert the guiding plate (N).
Ensure that the guides on the guiding
plate (1) are correctly located in the
guides of the ejection chute
extension (2).
● Fit screw (P) and tighten with nut (R).
● Screw in the screws (O) and tighten to
1 - 2 Nm.
2 Install the ejection chute plate
● Insert the ejection chute plate (M).
● Screw in the screws (O) and tighten to
1 - 2 Nm.
● Fit screws (Q) and tighten with nuts (R).
Any slight tensions occurring in the
ejection chute can be compensated by
readjusting the screws.
Tightening the screws of the
wheel carrier mounting
● Stand the machine up and check
for correct seating of all attached parts.
0478 216 9906 A - EN
● Tighten screws (1, 2) of the wheel
carrier mounting to 10 - 12 Nm.
After tightening screws, check that
both wheel carriers are securely
seated.

7.8 Fuel and engine oil

Top up engine oil before initial start
( engine instruction manual)!
Engine oil
Please consult the engine instruction
manual for the type of engine oil to be used
and the oil capacity. Check the oil filling
level at regular intervals ( see engine
instruction manual). Avoid exceeding or
falling below the correct oil level.
9
Fuel
Recommendation:
Fresh good quality fuel, normal unleaded
petrol ( engine instruction manual)! Use
a funnel when filling the tank with fuel (not
included in standard equipment). Note the
warnings in the section "For your safety".
( 4.)
Filling the fuel tank
● GH 460 C:
Open the tank ventilation screw (1).
● Unscrew the tank cap (2).
● Fill the fuel tank (use a funnel).
● Replace the tank cap (2).
GH 460 C:
Open the tank ventilation screw (1)
prior to initial operation of the
engine.
10

8. Controls

8.1 On- / Off switch

The On- / Off (1) switch is a
multifunction switch with the
following functions:
11
Safety switch:
The On- / Off switch (1) functions as a
safety switch. ( 10.)
Function enable switch during the
starting procedure:
The On- / Off switch (1) serves as the
main switch when starting the engine. The
engine cannot be started if the On- / Off
switch (1) is not operated. ( 11.1)
Switching off:
When the On- / Off switch (1) is released
by turning, the engine switches off and the
blade discs come to a standstill within a
few seconds (see Releasing the On- / Off
switch). ( 11.2)
Fastening screw for the feed chute:
The feed chute ATO 400 is detached by
unscrewing (anti-clockwise) the On- / Off
switch (1). The feed chute ATO 400 is
secured to the basic unit by screwing in
(clockwise) the On- / Off switch (1).
Operating the On- / Off switch:
● Press in the green button (2) (symbol I)
as far as it will go. The green button
locks into place and remains pressed
down.
The garden shredder can be started.
( 11.1)
12
57