For Your Child's Safety; Protection From Injury; Damage To The Product; Starting And Connecting The Devices - TIGEX Easy Protect Instrucciones De Uso

• If you are travelling, please always make sure that the
available voltage matches that given in the technical
data.

6.3 For your child's safety

Warning! Children cannot recognise the
dangers associated with using such devices.
They should therefore be kept away from them.
• Make sure that the unit and its accessories are always
kept out of baby's reach. The unit and its accessories
should always be at least 1 m away.
• Children are often poor judges of hazard and are liable
to injure themselves. You should therefore note:
– This device is not designed to be used by people
(including children) with physical, sensory or mental
disabilities or with insufficient experience and/or
knowledge, unless a person responsible for their
safety is supervising them or instructing them on
how to use the device.
– Children should be supervised to ensure that they
cannot play with the device.
– Make sure that the plastic packaging does not
become a lethal trap for children. There is a risk of
suffocation. Plastic packaging is not a toy.
– To avoid the possibility of strangulation, the power
cable must always be out of baby's reach.
• Use the unit only to give you additional safety. It can
never serve as a substitute for a human carer.

7.1 Parent unit

Mains operation
Only use the mains adapter supplied.
1. Insert the small plug of the mains adapter into the
mains adapter socket 9 of the parent unit.
2. Insert the plug into a power socket standard that
matches the rating given in the technical data (see
"11. Technical data" on page 42).
3. To turn on the parent unit 1 simply press the power ON/
OFF button 6.
Battery operation
For battery operation you need 3 batteries of the AAA 1.5 V
type. Any rechargeable batteries inserted will not be
recharged.
Attention! The batteries should be removed if the device is
not going to be used for an extended period to prevent
leaking batteries causing damage to the device.
1. Remove the battery cover 8 on the back of the parent
unit 1, by sliding it downwards.

7. Starting and connecting the devices

6.4 Protection from injury

Warning! Follow the instructions below to
prevent injuries.
• Make sure the power supply cable is tucked away
neatly to prevent anyone from tripping over it.

6.5 Damage to the product

Caution! To prevent damaging the product, follow the
instructions below.
• Do not expose the device to direct sunlight or extreme
heat as UV rays and overheating may make the plastic
brittle and the electronics could be damaged.
• The baby monitor should not be placed near to a
source of heat and the device should also not be
covered, to prevent it overheating.
• Never use the baby monitor in damp or wet
surroundings.
• Never use the baby monitor in dusty surroundings. This
could shorten the life of the device.
• Never use sharp or abrasive cleaning agents as these
could damage your device.
• While the devices are not in use, always switch them
off with the On/Off button 12 on the baby unit 10 and
the On/Off button 6 on the parent unit 1.
2. Insert the batteries, ensuring that they are correctly
positioned in the battery compartment according to the
+ and – symbols.
3. Slide the battery cover 8 back onto the parent unit 1.
4. To turn on the parent unit 1 simply press the power ON/
OFF button 6.
Is the battery level low the LED indicator 5 will flashing red.
The parent unit needs to be connected with the mains
adapter before the unit turns itself off automatcally. In
addiction a signal will also inform you about a low battery
status.
Note: If the mains adapter ist connected the device gets its
power from the mains adapter and not from the inserted
batteries.

7.2 Baby unit

The baby unit only works with the included mains adapter.
Warning! Ensure that the baby is not able to
touch the power cable. Also ensure that the unit
cannot fall into the cot.
40