Technical Data; Angle Grinder; Noise/Vibration Information; Battery Charging - Bosch GWS 18V-10 Professional Manual Original

Technical Data

Angle grinder

Article number
Rated voltage
A)
Rated speed
No-load speed
Max. grinding disc diameter
Grinding spindle thread
Max. thread length of grinding spindle
Kickback stop
Restart protection
Run-out brake
Speed preselection
Weight according to EPTA-Procedure 01:2014
– with additional low-vibration auxiliary handle
– with standard auxiliary handle
Recommended ambient temperature during
charging
Permitted ambient temperature during opera-
B)
tion and during storage
Recommended batteries
Recommended chargers
A) Depends on battery in use
B) Limited performance at temperatures <0 °C

Noise/Vibration Information

Noise emission values determined according to
EN 60745-2-3.
Typically, the A-weighted sound pressure level of the power
tool is 79 dB(A). Uncertainty K = 3 dB. The noise level when
working can exceed the volume stated. Wear hearing pro-
tection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745-2-3:
Surface grinding (roughing):
2 2
a =6.5 m/s , K=1.5 m/s ,
h
Grinding with abrasive disc:
2 2
a =3.5 m/s , K=1.5 m/s .
h
The vibration level given in these instructions has been
measured in accordance with a standardised measuring pro-
cedure and may be used to compare power tools. It can also
be used for a preliminary estimation of exposure to vibra-
tion.
The stated vibration level applies to the main applications of
the power tool. However, if the power tool is used for differ-
ent applications, with different application tools or poorly
maintained, the vibration level may differ. This can signific-
Bosch Power Tools
GWS 18V-10
3 601 JJ4 0..
V=
-1
min 9000
-1
min
mm
mm
A)
kg 2.6-2.8
kg 2.4-2.6
°C 0 to +35
°C –20 to +50
GBA 18V...
ProCORE18V...
GAL 18...
GAX 18...
GAL 36...
antly increase the exposure to vibration over the total work-
ing period.
To estimate the exposure to vibration accurately, the times
when the tool is switched off or when it is running but not ac-
tually being used should also be taken into account. This can
significantly reduce the exposure to vibration over the total
working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping the hands warm,
and organising workflows correctly.
Fitting

Battery Charging

Use only the chargers listed in the technical data. Only
u
these chargers are matched to the lithium-ion battery of
your power tool.
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
GWS 18V-10 GWS 18V-10
3 601 JJ4 0.. 3 601 JJ4 0..
18 18
9000
– –
100 115
M 10 M 14
22 22
● ●
● ●
● ●
– –
2.6-2.8
2.4-2.6
0 to +35
–20 to +50
GBA 18V...
ProCORE18V... ProCORE18V...
GAL 18...
GAX 18...
GAL 36...
1 609 92A 51X | (24.09.2019)
English | 21
18
9000
–
125
M 14
22
●
●
●
–
2.6-2.8
2.4-2.6
0 to +35
–20 to +50
GBA 18V...
GAL 18...
GAX 18...
GAL 36...