Intended Use; Product Features; Product Description And Specifications - Bosch GWS 18V-10 Professional Manual Original

20 | English
wires by applying excessive load to the brush The wire
bristles can easily penetrate light clothing and/or skin.
If the use of a guard is recommended for wire brush-
u
ing, do not allow any interference of the wire wheel or
brush with the guard. Wire wheel or brush may expand
in diameter due to work load and centrifugal forces.
Additional Safety Information
Wear safety goggles.
Use suitable detectors to determine if there are hid-
u
den supply lines or contact the local utility company
for assistance. Contact with electric cables can cause
fire and electric shock. Damaging gas lines can lead to ex-
plosion. Breaking water pipes causes property damage.
Do not touch grinding and cutting discs until they have
u
cooled down. The discs can become very hot while work-
ing.
Release the On/Off switch and set it to the Off posi-
u
tion when the power supply is interrupted, e.g. when
the battery pack is removed. This prevents uncontrolled
restarting.
Secure the workpiece. A workpiece clamped with
u
clamping devices or in a vice is held more secure than by
hand.
Do not open the battery. There is a risk of short-circuit-
u
ing.
Protect the battery against heat, e.g. against
continuous intense sunlight, fire, dirt, water
and moisture. There is a risk of explosion and
short-circuiting.
In case of damage and improper use of the battery, va-
u
pours may be emitted. The battery can set alight or ex-
plode. Ensure the area is well ventilated and seek medical
attention should you experience any adverse effects. The
vapours may irritate the respiratory system.
Only use the battery with products from the manufac-
u
turer. This is the only way in which you can protect the
battery against dangerous overload.
The battery can be damaged by pointed objects such
u
as nails or screwdrivers or by force applied externally.
An internal short circuit may occur, causing the battery to
burn, smoke, explode or overheat.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
1 609 92A 51X | (24.09.2019)
Please observe the illustrations at the beginning of this oper-
ating manual.

Intended use

The power tool is intended for cutting, roughing and brush-
ing metal and stone materials, as well as making holes in
stone materials using diamond core cutters, without the use
of water.
A special protective guard for cutting must be used when
cutting bonded abrasives.
Sufficient dust extraction must be provided when cutting
stone.
With approved abrasive tools, the power tool can be used for
sanding with sanding discs.
The power tool must not be used to grind concrete.

Product Features

The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Unlocking lever for protective guard
(2) Direction of rotation arrow on housing
Spindle lock button
(3)
(4) On/off switch
A)
(5) Battery
A)
(6) Battery release button
(7) Auxiliary handle (insulated gripping surface)
(8) Protective guard for grinding
(9) Mounting flange with O‑ring (M14)
(10) Grinding disc
(11) Quick-clamping nut with bar (M14)
(12) Clamping nut (M10)
(13) Protective guard for cutting
A)
(14) Cutting disc
(15) Handle (insulated gripping surface)
(16) Grinding spindle
A)
(17) Hand guard
A)
(18) Rubber sanding pad
A)
(19) Abrasive disc
A)
(20) Round nut
A)
(21) Cup brush
A)
(22) Diamond core bit
(23) Button for battery charge indicator
A)
(24) Battery charge indicator
(25) Extraction guard for cutting with a guide block
A)
(26) Diamond cutting disc
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
A)
A)
A)
Bosch Power Tools