MTD 760 Serie Manual De Operador página 11

EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.
1. Remove the hex screw (or knob screw if applicable) from
PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIE
the bottom of seat. See (a) in Figure 3-6.
2. Position the seat facing forward over the seat pivot bracket,
with the two forward seat mount tabs fitting into the provided
EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.
grooves in the seat pivot bracket. See (b) in Figure 3-6.
3. Slide the seat rearward and align the center mounting
hole in the seat with the slot in the seat pan. Insert the hex
PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIE
screw (or knob screw if applicable) previously removed. Do
not tighten at this point.
4. Adjust the seat to the optimal operator preferred location,
this may mean actually sitting in the seat to decide what
EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.
feels best to the operator. Keep in mind the operator needs
to be able to fully operate all pedals comfortably while
sitting back in the seat.
PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIE
5. Tighten the hex screw (or knob screw if applicable) at this time.
EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.
PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIE
EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.
PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIE
EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.
b
PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIE
6. To adjust the position of the seat, remove the hex screw (or
EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.
knob screw if applicable) on the bottom of the seat. Slide
the seat forward or backward as desired. Re-install the hex
screw (or knob screw if applicable). See Figure 3-7.
PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIE
EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.
PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIE
EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.
PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIE
EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.
PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIE
a
Figure 3-6
Figure 3-7
Mulch Plug (if equipped)
On tractor models so equipped, a mulch plug can be found
within the cutting deck's discharge opening.
NOTE: Refer to Mulching in the "Operation" section of this
manual for more detailed information.
If you'd prefer to operate the cutting deck without mulching,
simply remove the mulch plug by un-threading the plastic
wing nut which fastens it to the cutting deck. This will allow
the clippings to discharge out of the discharge opening during
operation. See Figure 3-8.
Figure 3-8
Note: See the Attachments & Accessories section if you would
like information regarding adding a mulching system for your
model of tractor.
Tire Pressure
WARNING!
Maximum tire pressure under any
circumstances is 30 psi. Equal tire pressure should be
maintained at all times. Never exceed the maximum
inflation pressure shown on the sidewall of the tire.
The recommended operating tire pressure is:
• Approximately 10 psi for the rear tires
• Approximately 14 psi for the front tires
IMPORTANT:
Refer to the tire sidewall for exact tire
manufacturer's recommended or maximum psi. Do not
overinflate. Uneven tire pressure could cause the cutting deck to
mow unevenly.
Gas and Oil Fill-up
Oil
IMPORTANT:
Your tractor is shipped with motor oil in the
engine. However, you MUST check the oil level before operating.
Be careful not to overfill.
Service and check the engine oil as instructed in the separate
Engine Operator/Owner Manual packed with your tractor. Read
the instructions carefully.
S
ection
3 — A & S -U
SSembly et p
11