Daspi SKY C Serie Manual De Instrucciones página 10

g
eneral safety rules
congratulations on choosing one of our products. Your new
electromechanical gear motor is a top quality product, designed
to be long-lasting and reliable so as to guarantee long term
performance and safety. attached to this booklet you will find all
the information you need to assemble your gear motor and ensure
your safety.
All our products are built to comply with current legislation.
We recommend that you use only original parts both during
assembly and when performing maintenance. You cannot be too
careful, and caution is the best rule for preventing accidents.
W
arning
unskilled personnel should never be allowed to assemble, repair or
adjust the equipment, and before commencing work all necessary
precautions must be taken to prevent accidents: power supply
disconnected (including backup batteries if present). All moving
parts must be fitted with suitable safety guards.
WArNINg: Any use of this product that is not intended by this
instruction booklet and/or any unauthorised modification to the
product or its components relieves DASPI of any liability arising
from consequent damage or injury to property, people or animals.
Keep this handbook carefully, attaching it to the technical installation
leaflet and storing it where it is available to anyone who may need
it and make sure said personnel are aware of this.
dispose of the packing material after installation (cardboard, plastic,
polystyrene etc.) in compliance with local legislation, bearing
in mind that plastic bags can be very dangerous when children
are around. instruct the people who are to use the automation,
s m
eCuriTy eChanism
disTanCe in mouVemenT
tyPE oF PRoduCt
the sKY c gear motor has been designed to open spring overhead and
sectional doors, daspi will assume no liability for any unintended or
improper use of the sKY gear motor.
WArNINg: The SKY C gear motor does not have a mechanical clutch and
must therefore be installed in combination with the appropriate DASPI
control unit or with a control unit provided with an electronic clutch.
uSInG tHE AutoMAtIon
Important safety instructions
It is vitally important for the safety of the people involved to take great
care and meticulously follow the instructions below.
Keep these instructions safely. Do not allow children to play with the
fixed and movable controls of the gate. Keep remote control handsets
for the gate out of the reach of children.
given that the automation can be controlled remotely or on sight by
pushbutton or remote control handset, it is essential to make frequent
checks to ensure that all the safety devices are in perfect working order.
We recommend having the electronic clutch checked regularly (every six
months) by skilled personnel. to calibrate this protection device, see the
section "adjusting the electronic clutch" in the electronic control unit
instruction booklet.
PRELIMInARy CHECKS
read the contents of this handbook with great care.
Make sure the product has not been damaged during transport.
Make sure that the door has a solid structure, that its movement is
properly balanced and that there are no friction points. Make sure that
the electrical equipment corresponds with the specifications for the gear
motor. Make sure that a suitable earth system has been installed and
that all metal parts of the installation are connected to it.
EnGLISH
d e
o noT insTall The leCTriC
auTomaTion in PlaCe Full
oF exPlosiVe moisTures
informing them about the control and safety systems installed in
the structure. this product is not suitable for installation in explosive
atmospheres.
M
aintenance
Warning: for all types of maintenance, first disconnect the power
supply. to correctly maintain the system containing the sKY gear
motor, proceed as follows:
check the tension of the chain regularly. ask a skilled person to
adjust the electronic clutch (see the section in the electronic control
unit handbook). lubricate the sliding guides, the cables and lifting
arms of the door regularly. in case of faulty operation, consult skilled
personnel.
d
eMolition
Material should be disposed of in accordance with the legislation
in force. We recommend separating materials by type for recycling
(copper, aluminium, plastic, electrical parts etc.). in any case, none
of the materials are considered hazardous to their handlers.
d
isMantling
to dismantle the automation or transfer it to another site it is
necessary to:
disconnect the power supply and disconnect the electrical
equipment;
dismantle the control panel and all the components of the
installation;
if some parts are found to be damaged or cannot be removed,
arrange to replace them.
u
shoCK se
The gloVes
Make sure that it is always easy to manoeuvre the door manually.
Bear in mind that the automation is a tool for facilitating use of the door
and does not solve problems due to defective or poor installation or to
failure to maintain the door itself.
InStALLAtIon
Important safety instructions for installation.
Warning: Incorrect installation may cause serious damage or injury.
Follow all the instructions below scrupulously to install the automation
correctly.
ASSEMBLInG tHE SLIdInG GuIdE And tHE MotoR
The sliding guide is available in parts that are 1 - 1.5 – 3 metres long.
prepare brackets "s1" for connecting the guide (only for the version in
1-1.5 m pieces) by fitting the 4 screws "V1" and the 4 nuts "d1" for each
bracket (figure 1).
on a plane surface position the parts of the guide that are needed to
reach a working length to completely open the door to be automated,
bearing in mind that for standard doors up to 2.50 m a 3m guide is
needed (figure 2).
connect the various parts by inserting, into the appropriate housings "a"
of the guide, nuts "d1" that had been fitted previously to brackets "s1"
and fasten screws "V1" , making sure that the parts are positioned exactly
head to head (fig. 2).
assemble bracket "s2" on the motor support using the appropriate
screws "V2" and washers "r1" , insert the previously assembled guide in
the appropriate housing "B" and fasten it down (fig.3).
inside the sliding guide insert shoe "c", positioning it so that housing "d"
is facing the door (fig. 4).
assemble chain-tightener bracket "s3" by first inserting screw "V3" , then
pin "e" and gear "F" then lock pin "e" with nut"d2" and washer "r2"
(fig. 5).
insert one end of the chain "g" and run it along the appropriate housing
"H" of the sliding guide until it comes out at the other side (fig. 6).
pass the other end of the chain inside the chain-tightener bracket, slide
u K
se glasses eeP The ProTeCTion
For Welding CarTer