Makita DLS600 Manual De Instrucciones página 22

Miter cutting
Refer to the section for adjusting the miter angle.
Bevel cut
WARNING:
After setting the blade for a bevel
cut, before operating the tool ensure that the saw
head and blade will have free travel throughout
the entire range of the intended cut. Interruption
of the saw head or blade travel during the cutting
operation may result in kickback and serious personal
injury.
WARNING:
While making a bevel cut keep
hands out of the path of the blade. The angle of the
blade may confuse the operator as to the actual blade
path while cutting and contact with the blade will
result in serious personal injury
WARNING:
The blade should not be raised
until it has come to a complete stop. During a
bevel cut the piece cut off may come to rest against
the blade. If the blade is raised while it is rotating the
cut-off piece maybe ejected by the blade causing
the material to fragment which may result in serious
personal injury.
WARNING:
Always remove sub-fence when
performing bevel cuts. Failure to do so may cause
serious injury.
► Fig.47
1. Loosen the lever and tilt the saw blade to set the
bevel angle (Refer to the previously covered "Adjusting
the bevel angle"). Be sure to retighten the lever firmly to
secure the selected bevel angle safely.
2. Secure the workpiece with the vise.
3. Switch on the tool without the blade making any
contact and wait until the blade attains full speed.
4.
Gently lower the handle to the fully lowered position while
applying pressure in parallel with the blade to cut the workpiece.
5. When the cut is completed, switch off the tool and
wait until the blade has come to a complete stop
before returning the blade to its fully elevated position.
NOTICE:
When pressing down the handle, apply
pressure in parallel with the blade. If a force is
applied perpendicularly to the turn base or if the pres-
sure direction is changed during a cut, the precision
of the cut will be impaired.
Compound cutting
Compound cutting is the process in which a bevel
angle is made at the same time in which a miter angle
is being cut on a workpiece. Compound cutting can be
performed at the angle shown in the table.
Miter angle
Left and right 45°
Right 52°
Left 52°
When performing compound cutting, refer to "Press
cutting", "Miter cutting" and "Bevel cut" explanations.
Bevel angle
Left and right 0° - 45°
Left 20° - Right 45°
Left 45° - Right 20°
22 ENGLISH
Cutting aluminum extrusion
► Fig.48: 1. Vise 2. Spacer block 3. Guide fence
4. Aluminum extrusion 5. Spacer block
When securing aluminum extrusions, use spacer blocks
or pieces of scrap as shown in the figure to prevent
deformation of the aluminum. Use a cutting lubricant
when cutting the aluminum extrusion to prevent build-up
of the aluminum material on the blade.
CAUTION:
Never attempt to cut thick or round
aluminum extrusions. Thick aluminum extrusions
may come loose during operation and round alumi-
num extrusions cannot be secured firmly with this
tool.
Cutting repetitive lengths
When cutting several pieces of stock to the same
length, ranging from 200 mm to 330 mm, use the set
plate (optional accessory). Install the set plate on the
holder (optional accessory) as shown in the figure.
► Fig.49: 1. Set plate 2. Holder 3. Screw
Align the cutting line on your workpiece with either the
left or right side of the groove in the kerf board, and
while holding the workpiece, move the set plate flush
against the end of the workpiece. Then secure the set
plate with the screw.
When the set plate is not used, loosen the screw and
turn the set plate out of the way.
Carrying tool
WARNING:
Stopper pin is only for carrying
and storage purposes and should never be used
for any cutting operations. The use of the stopper
pin for cutting operations may cause unexpected
movement of the saw blade resulting in kickback and
serious personal injury.
CAUTION:
Always secure all moving portions
before carrying the tool. If portions of the tool move
while being carried loss of control or balance may
occur resulting in personal injury.
1. Remove the battery cartridge.
2. Secure the blade at 0° bevel angle and the turn
base at the full right miter angle position.
► Fig.50: 1. Turn base
3. Lower the handle fully and lock it in the lowered
position by pushing in the stopper pin.
4. Carry the tool by holding the handle.
► Fig.51