Troubleshooting; Maintenance; Service - Delta DP350 Manual De Instrucciones

For assistance with your machine, visit our website at www.deltaportercable.com for a list of service centers or call the
DELTA Machinery help line at 1-800-223-7278 (In Canada call 1-800-463-3582).
kEEP MACHINE CLEAN
Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp
cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material.
Wear certified safety equipment for eye, hearing and respiratory protection while using compressed air.
FAILURE TO START
Should your machine fail to start, check to make sure the prongs on the cord plug are making good contact in the
outlet. Also, check for blown fuses or open circuit breakers in the line.
LUBRICATION & RUST PROTECTION
Apply household floor paste wax to the machine table, extension table or other work surface weekly. Or use a commercially
available protective product designed for this purpose. Follow the manufacturer's instructions for use and safety.
To clean cast iron tables of rust, you will need the following materials: a sheet of medium Scotch-Brite™ Blending Hand
Pad, a can of WD-40 ® and a can of degreaser. Apply the WD-40 and polish the table surface with the Scotch-Brite pad.
Degrease the table, then apply the protective product as described above.
REPLACEMENT PARTS
Use only identical replacement parts. For a parts list or to order parts, visit our website at servicenet.deltamachinery.com. You
can also order parts from your nearest factory-owned branch, or by calling our Customer Care Center at 1-800-223-7278 to
receive personalized support from highly-trained technicians.
FREE WARNINg LABEL REPLACEMENT
If your warning labels become illegible or are missing, call 1-800-223-7278 for a free replacement.
TO REDUCE THE RISK OF INJURY READ
INSTRUCTION MANUAL BEFORE OPERATING
DRILL PRESS. ALWAYS WEAR EYE PROTECTION
AND WEAR PROPER RESPIRATORY
PROTECTION. DO NOT WEAR GLOVES,
NECKTIES, JEWELRY, LOOSE CLOTHING OR
LONG HAIR. ALWAYS CLAMP WORKPIECE OR
BRACE IT AGAINST COLUMN TO PREVENT
ROTATION. KEEP HANDS AWAY FROM ROTATING
BIT OR ACCESSORY. USE RECOMMENDED
SPEED FOR THE DRILL AND WORKPIECE
MATERIAL. BE SURE DRILL BIT OR CUTTING
TOOL IS NOT DAMAGED AND PROPERLY
LOCKED IN THE CHUCK BEFORE OPERATING.
MAKE CERTAIN CHUCK KEY IS REMOVED
BEFORE STARTING DRILL PRESS. DISCONNECT
MACHINE FROM POWER SOURCE BEFORE
MAKING REPAIRS OR ADJUSTMENTS. DO NOT
EXPOSE TO RAIN OR USE IN DAMP LOCATIONS.

TROUBLESHOOTINg

MAINTENANCE

SERVICE

ADJUST SPEED ONLY WHILE
MACHINE IS RUNNING.
AJUSTE LA VELOCIDAD SOLAMENTE
MIENTRAS LA MÁQUINA ESTÉ EN
FUNCIONAMIENTO.
RÉGLER LA VITESSE UNIQUEMENT
LORSQUE L'APPAREIL EST
EN MARCHE.
PARA REDUCIR EL RIESGO DE LESIONES LEA EL MANUAL
DE INSTRUCCIONES ANTES DE OPERAR LA PRENSA DE
TALADRO. SIEMPRE UTILICE PROTECCIÓN PARA LOS OJOS
Y PROTECCIÓN PARA LA RESPIRACIÓN. NO USE GUANTES,
CORBATAS, JOYAS, ROPA HOLGADA NI EL CABELLO
LARGO. SIEMPRE SUJETE LA PIEZA DE TRABAJO CON
ABRAZADERAS O AMÁRRELA CONTRA LA COLUMNA
PARA EVITAR LA ROTACIÓN. MANTENGA LAS MANOS
LEJOS DE LA BROCA O ACCESORIOS GIRATORIOS. USE LA
VELOCIDAD RECOMENDADA PARA EL TALADRO Y EL
MATERIAL DE LA PIEZA DE TRABAJO. ASEGÚRESE DE QUE
LA BROCA DEL TALADRO O LA HERRAMIENTA DE CORTE
NO ESTÉN DAÑADAS Y DE QUE ESTÉN CORRECTAMENTE
BLOQUEADAS EN EL PORTABROCAS ANTES DE SU
OPERACIÓN. ASEGÚRESE DE RETIRAR LA LLAVE DE
PORTABROCAS ANTES DE ENCENDER LA PRENSA DE
TALADRO. DESCONECTE LA MÁQUINA DE LA FUENTE DE
ALIMENTACIÓN ANTES DE REALIZAR REPARACIONES O
AJUSTES. NO EXPONGA A LA LLUVIA NI UTILICE EN
LUGARES HÚMEDOS.
14
POUR RÉDUIRE LE RISQUE DE BLESSURES, LIRE LE MODE
D'EMPLOI AVANT L'UTILISATION DE LA PERCEUSE À
COLONNE. TOUJOURS PORTER UNE PROTECTION
OCULAIRE ET DES ARTICLES DE PROTECTION DES VOIES
RESPIRATOIRES. NE PAS PORTER DE GANTS, DE
CRAVATES, DE BIJOUX NI DE VÊTEMENTS AMPLES;
COUVRIR LES CHEVEUX LONGS. TOUJOURS FIXER LA
PIÈCE OU BIEN LA CALER CONTRE LA COLONNE POUR
EMPÊCHER UNE ROTATION. TENIR VOS MAINS ÉLOIGNÉES
DE LA MÈCHE ROTATIVE OU ACCESSOIRE. UTILISER LA
VITESSE RECOMMANDÉE POUR LA PERCEUSE ET LE
MATÉRIEL DE LA PIÈCE À PERCER. S'ASSURER QUE LA
MÈCHE OU L'ORGANE DE COUPE N'EST PAS ENDOMMAGÉ
ET QU'IL EST BIEN VERROUILLÉ DANS LE MANDRIN AVANT
SON UTILISATION. S'ASSURER DE RETIRER LA CLÉ DU
MANDRIN AVANT DE DÉMARRER LA PERCEUSE DE
COLONNE. DÉBRANCHER LA MACHINE DE LA SOURCE
D'ALIMENTATION AVANT D'EFFECTUER DES RÉPARATIONS
OU DES RÉGLAGES. NE PAS L'EXPOSER À LA PLUIE ET NE
PAS L'UTILISER DANS UN ENDROIT HUMIDE.
A21573